AGCO-ALLIS 9815 or Deutz-Fahr DX 250?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 9815 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 250 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The AGCO-ALLIS 9815 suits road haulage better on this data: 33% (10.0 km/h / 6.2 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 9815 | DX 250 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 160.3 kW (215.0 hp)Traktorenlexikon, “AGCO-Allis 9815” | 162 kW (217 hp)Traktorenlexikon, “Deutz-Fahr DX 250” | Not comparableNot comparable on power at the PTO shaft: the 9815 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 250 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 9815 and the DX 250. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 9815 and the DX 250. |
| Which pumps more oil for implements? | 105.2 L/min (27.8 gpm)Traktorenlexikon, “AGCO-Allis 9815” | 81 L/min (21.4 gpm)Traktorenlexikon, “Deutz-Fahr DX 250” | AheadThe AGCO-ALLIS 9815 has 30% more hydraulic flow (24.2 L/min / 6.4 gpm) than the Deutz-Fahr DX 250 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 5,948 kg (13,113 lb)Traktorenlexikon, “AGCO-Allis 9815” | 8,150 kg (17,968 lb)Traktorenlexikon, “Deutz-Fahr DX 250” | AheadThe Deutz-Fahr DX 250 has 37% more lift (2,202 kg / 4,855 lb) than the AGCO-ALLIS 9815 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 8,894 kg (19,608 lb)Traktorenlexikon, “AGCO-Allis 9815” | 9,250 kg (20,393 lb)Traktorenlexikon, “Deutz-Fahr DX 250” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | 12,000 kg (26,455 lb)Traktorenlexikon, “Deutz-Fahr DX 250” | No figureNo call on maximum permissible mass: no figure on record for the 9815. |
| Which has the wider choice of gears? | 18Traktorenlexikon, “AGCO-Allis 9815” | 18Traktorenlexikon, “Deutz-Fahr DX 250” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 9815 and the DX 250. |
| Which is faster on the road? | 40 km/h (24.9 mph)Traktorenlexikon, “AGCO-Allis 9815” | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Fahr DX 250” | AheadThe AGCO-ALLIS 9815 has 33% more top speed (10.0 km/h / 6.2 mph) than the Deutz-Fahr DX 250 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 1000 rpmTraktorenlexikon, “AGCO-Allis 9815” | 923 rpmTraktorenlexikon, “Deutz-Fahr DX 250” | No figureNo call on PTO speeds: no standard PTO speed stated for the DX 250. |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “AGCO-Allis 9815” | independentTraktorenlexikon, “Deutz-Fahr DX 250” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “AGCO-Allis 9815” | 4WDTraktorenlexikon, “Deutz-Fahr DX 250” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1994–1998 | 1982–1983 | Ahead (a fact, not an advantage)The AGCO-ALLIS 9815 is newer: production began 12 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The AGCO-ALLIS 9815 has 30% more hydraulic flow (24.2 L/min / 6.4 gpm) than the Deutz-Fahr DX 250 (both pump flow, as stated by the source).
- The Deutz-Fahr DX 250 has 37% more lift (2,202 kg / 4,855 lb) than the AGCO-ALLIS 9815 (both lift at the hitch ends, as stated by the source).
- The AGCO-ALLIS 9815 has 33% more top speed (10.0 km/h / 6.2 mph) than the Deutz-Fahr DX 250 (both top speed forward, as stated by the source).
- The AGCO-ALLIS 9815 is newer: production began 12 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 9815 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 250 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO speeds.
← Every figure for both machines, side by side, with sources