AGCO-ALLIS 9670 or Fiat 1880 (DT)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 9670 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 1880 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The AGCO-ALLIS 9670 suits loader and hydraulic implement work better on this data: 32% (18.0 L/min / 4.8 gpm) more hydraulic flow.
- The AGCO-ALLIS 9670 suits road haulage better on this data: 33% (10.0 km/h / 6.2 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 9670 | 1880 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 130.2 kW (174.6 hp)Traktorenlexikon, “AGCO-Allis 9670” | 132.5 kW (177.7 hp)Traktorenlexikon, “Fiat 1880 DT” | Not comparableNot comparable on power at the PTO shaft: the 9670 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 1880 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 9670 and the 1880 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 9670 and the 1880 (DT). |
| Which pumps more oil for implements? | 73.8 L/min (19.5 gpm)Traktorenlexikon, “AGCO-Allis 9670” | 55.8 L/min (14.7 gpm)Traktorenlexikon, “Fiat 1880 DT” | AheadThe AGCO-ALLIS 9670 has 32% more hydraulic flow (18.0 L/min / 4.8 gpm) than the Fiat 1880 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 5,900 kg (13,007 lb)Traktorenlexikon, “Fiat 1880 DT” | No figureNo call on three-point lift: no figure on record for the 9670. |
| Which is heavier, for traction? | 7,303 kg (16,100 lb)Traktorenlexikon, “AGCO-Allis 9670” | 6,480 kg (14,286 lb)Traktorenlexikon, “Fiat 1880 DT” | Ahead (a fact, not an advantage)The AGCO-ALLIS 9670 is 13% heavier (823 kg / 1,814 lb) than the Fiat 1880 (DT) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | 10,000 kg (22,046 lb)Traktorenlexikon, “Fiat 1880 DT” | No figureNo call on maximum permissible mass: no figure on record for the 9670. |
| Which has the wider choice of gears? | 18Traktorenlexikon, “AGCO-Allis 9670” | 12 to 24Traktorenlexikon, “Fiat 1880 DT” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 9670 and the 1880 (DT). |
| Which is faster on the road? | 40 km/h (24.9 mph)Traktorenlexikon, “AGCO-Allis 9670” | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “Fiat 1880 DT” | AheadThe AGCO-ALLIS 9670 has 33% more top speed (10.0 km/h / 6.2 mph) than the Fiat 1880 (DT) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 1000 rpmTraktorenlexikon, “AGCO-Allis 9670” | 540/1000 rpmTraktorenlexikon, “Fiat 1880 DT” | AheadThe Fiat 1880 (DT) offers 540 rpm at the PTO, which the AGCO-ALLIS 9670 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “AGCO-Allis 9670” | independentTraktorenlexikon, “Fiat 1880 DT” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “AGCO-Allis 9670” | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 1880 DT” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1994–1995 | 1979–1984 | Ahead (a fact, not an advantage)The AGCO-ALLIS 9670 is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The AGCO-ALLIS 9670 has 32% more hydraulic flow (18.0 L/min / 4.8 gpm) than the Fiat 1880 (DT) (both pump flow, as stated by the source).
- The AGCO-ALLIS 9670 is 13% heavier (823 kg / 1,814 lb) than the Fiat 1880 (DT) (both unladen weight, as stated by the source).
- The AGCO-ALLIS 9670 has 33% more top speed (10.0 km/h / 6.2 mph) than the Fiat 1880 (DT) (both top speed forward, as stated by the source).
- The Fiat 1880 (DT) offers 540 rpm at the PTO, which the AGCO-ALLIS 9670 does not (as stated by the sources).
- The AGCO-ALLIS 9670 is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 9670 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 1880 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources