AGCO-ALLIS 9630 or VALMET 8350?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 9630 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8350 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 9630 | 8350 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 99.3 kW (133.2 hp)Traktorenlexikon, “AGCO-Allis 9630” | 99.3 kW (133.2 hp)Traktorenlexikon, “Valmet Mega-8350” | Not comparableNot comparable on power at the PTO shaft: the 9630 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8350 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 9630 and the 8350. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 9630 and the 8350. |
| Which pumps more oil for implements? | 85.6 L/min (22.6 gpm)Traktorenlexikon, “AGCO-Allis 9630” | 76.4 L/min (20.2 gpm)Traktorenlexikon, “Valmet Mega-8350” | AheadThe AGCO-ALLIS 9630 has 12% more hydraulic flow (9.2 L/min / 2.4 gpm) than the VALMET 8350 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,158 kg (6,962 lb)Traktorenlexikon, “AGCO-Allis 9630” | 6,800 kg (14,991 lb)Traktorenlexikon, “Valmet Mega-8350” | AheadThe VALMET 8350 has 115% more lift (3,642 kg / 8,029 lb) than the AGCO-ALLIS 9630 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 6,714 kg (14,802 lb)Traktorenlexikon, “AGCO-Allis 9630” | 6,490 kg (14,308 lb)Traktorenlexikon, “Valmet Mega-8350” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | 9,000 kg (19,842 lb)Traktorenlexikon, “Valmet Mega-8350” | No figureNo call on maximum permissible mass: no figure on record for the 9630. |
| Which has the wider choice of gears? | 18Traktorenlexikon, “AGCO-Allis 9630” | 36Traktorenlexikon, “Valmet Mega-8350” | AheadThe VALMET 8350 has 100% more forward gears (18 gears) than the AGCO-ALLIS 9630 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 9630 and the 8350. |
| Which is faster on the road? | 40 km/h (24.9 mph)Traktorenlexikon, “AGCO-Allis 9630” | 40 km/h (24.9 mph) to 50 km/h (31.1 mph)Traktorenlexikon, “Valmet Mega-8350” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “AGCO-Allis 9630” | 540/1000 rpmTraktorenlexikon, “Valmet Mega-8350” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “AGCO-Allis 9630” | independentTraktorenlexikon, “Valmet Mega-8350” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “AGCO-Allis 9630” | 4WDTraktorenlexikon, “Valmet Mega-8350” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1993–1995 | 1998–2004 | Ahead (a fact, not an advantage)The VALMET 8350 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The AGCO-ALLIS 9630 has 12% more hydraulic flow (9.2 L/min / 2.4 gpm) than the VALMET 8350 (both pump flow, as stated by the source).
- The VALMET 8350 has 115% more lift (3,642 kg / 8,029 lb) than the AGCO-ALLIS 9630 (both lift at the hitch ends, as stated by the source).
- The VALMET 8350 has 100% more forward gears (18 gears) than the AGCO-ALLIS 9630 (both forward gears, as stated by the source).
- The VALMET 8350 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 9630 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8350 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources