AGCO-ALLIS 7630 or DEUTZ-ALLIS 7120?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 7630 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 7120 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The DEUTZ-ALLIS 7120 suits loader and hydraulic implement work better on this data: 42% (26.8 L/min / 7.1 gpm) more hydraulic flow and 20% (1,100 kg / 2,425 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 7630 | 7120 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 91.2 kW (122.3 hp)Traktorenlexikon, “AGCO-Allis 7630” | 91.2 kW (122.3 hp)Traktorenlexikon, “Deutz-Allis 7120” | Not comparableNot comparable on power at the PTO shaft: the 7630 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 7120 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 7630 and the 7120. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 7630 and the 7120. |
| Which pumps more oil for implements? | 64.0 L/min (16.9 gpm)Traktorenlexikon, “AGCO-Allis 7630” | 90.8 L/min (24.0 gpm)Traktorenlexikon, “Deutz-Allis 7120” | AheadThe DEUTZ-ALLIS 7120 has 42% more hydraulic flow (26.8 L/min / 7.1 gpm) than the AGCO-ALLIS 7630 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 5,400 kg (11,905 lb)Traktorenlexikon, “AGCO-Allis 7630” | 6,500 kg (14,330 lb)Traktorenlexikon, “Deutz-Allis 7120” | AheadThe DEUTZ-ALLIS 7120 has 20% more lift (1,100 kg / 2,425 lb) than the AGCO-ALLIS 7630 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 5,170 kg (11,398 lb)Traktorenlexikon, “AGCO-Allis 7630” | 5,100 kg (11,244 lb)Traktorenlexikon, “Deutz-Allis 7120” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 8,100 kg (17,857 lb)Traktorenlexikon, “AGCO-Allis 7630” | — | No figureNo call on maximum permissible mass: no figure on record for the 7120. |
| Which has the wider choice of gears? | 24Traktorenlexikon, “AGCO-Allis 7630” | 24 to 32Traktorenlexikon, “Deutz-Allis 7120” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 7630 and the 7120. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “AGCO-Allis 7630” | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Allis 7120” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “AGCO-Allis 7630” | 540/1000 rpmTraktorenlexikon, “Deutz-Allis 7120” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “AGCO-Allis 7630” | independentTraktorenlexikon, “Deutz-Allis 7120” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “AGCO-Allis 7630” | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Allis 7120” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1991–1992 | 1986–1989 | Ahead (a fact, not an advantage)The AGCO-ALLIS 7630 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The DEUTZ-ALLIS 7120 has 42% more hydraulic flow (26.8 L/min / 7.1 gpm) than the AGCO-ALLIS 7630 (both pump flow, as stated by the source).
- The DEUTZ-ALLIS 7120 has 20% more lift (1,100 kg / 2,425 lb) than the AGCO-ALLIS 7630 (both lift at the hitch ends, as stated by the source).
- The AGCO-ALLIS 7630 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 7630 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 7120 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources