11 material differences · fewer than 12
Tractor oneAGCO-ALLIS 56801991–1997No measured PTO figureTractor twoVALMET 46001993–1996No measured PTO figure
Which should you choose?
Read our verdict on the 5680 and the 4600 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 6 fields identical or within 5%, which is not counted as material
| Field | 5680 | 4600 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 78.9 hp | 78.9 hp | — |
| Engine declared | S.L.H. 1000.4 A-1 | VALMET 420 D | differs |
| Displacement declared | 4.00 L | 4.40 L | +10% 4600 |
| Maximum torque declared | 193 lb·ft · 261 N·m | 214 lb·ft · 290 N·m | +11% 4600 |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Pedal-operated dry SAME double clutch | Dry double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 10.7 gpm · 40.5 L/min | 10.3 gpm · 39.0 L/min | — |
| Pressure declared | 3,046 psi · 210 bar | 2,901 psi · 200 bar | — |
| Three-point lift, at the coupling points declared | 6,790 lb · 3,080 kg | 6,294 lb · 2,855 kg | +8% 5680 |
| Rear PTO speeds declared | 540/1000 rpm | 540E/540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,669 lb · 3,025 kg | 6,945 lb · 3,150 kg | — |
| Maximum permissible mass declared | 11,464 lb · 5,200 kg | — | — |
| Wheelbase declared | 92.9 in · 2,360 mm | 94.0 in · 2,387 mm | — |
| Length declared | 154.3 in · 3,919 mm | 149.2 in · 3,790 mm | — |
| Width declared | 76.4–97.0 in · 1,941–2,464 mm | 81.5 in · 2,070 mm | differs |
| Ground clearance declared | 19.7 in · 500 mm | 17.1 in · 435 mm | +15% 5680 |
| Turning radius, braked declared | 9.2 ft · 2.80 m | 14.8 ft · 4.50 m | +61% 4600 |
| Fuel tank declared | 83.5 qt · 79.0 L | 100.4 qt · 95.0 L | +20% 4600 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 5680 sources
Source
- Source: Traktorenlexikon, “AGCO-Allis 5680”
VALMET 4600 sources
Source
- Source: Traktorenlexikon, “Valmet 4600”
- Source: Traktorenlexikon, “Valmet 665”