9 material differences · fewer than 12
Tractor oneAGCO-ALLIS 46601991–1997No measured PTO figureTractor twoCASE-INTERNATIONAL 595 (DT)1990–1993No measured PTO figure
Which should you choose?
Read our verdict on the 4660 and the 595 (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 6 fields identical or within 5%, which is not counted as material
| Field | 4660 | 595 (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 59.1 hp | 59.1 hp | — |
| Engine declared | SAME 1.053 P | IHC D-206 | differs |
| Displacement declared | 3.12 L | 3.38 L | +9% 595 (DT) |
| Maximum torque declared | 144 lb·ft · 195 N·m | 162 lb·ft · 220 N·m | +13% 595 (DT) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry double clutch | Pedal-operated dry Laycock single-disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 8.5 gpm · 32.0 L/min | — | — |
| Pressure declared | 1,740 psi · 120 bar | — | — |
| Three-point lift, at the coupling points declared | 4,630 lb · 2,100 kg | 4,409 lb · 2,000 kg | — |
| Rear PTO speeds declared | 540 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 4,762 lb · 2,160 kg | 6,440 lb · 2,921 kg | +35% 595 (DT) |
| Wheelbase declared | 82.1 in · 2,085 mm | 84.5 in · 2,146 mm | — |
| Length declared | 143.7 in · 3,650 mm | 142.0 in · 3,607 mm | — |
| Width declared | 69.3–86.4 in · 1,760–2,195 mm | 75.0 in · 1,905 mm | differs |
| Ground clearance declared | 18.1 in · 460 mm | 22.1 in · 561 mm | +22% 595 (DT) |
| Turning radius, braked declared | 11.6 ft · 3.55 m | 11.7 ft · 3.56 m | — |
| Fuel tank declared | 58.1 qt · 55.0 L | 80.0 qt · 75.7 L | +38% 595 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 4660 sources
- Source: Traktorenlexikon, “AGCO-Allis 4660”
- Source: Traktorenlexikon, “SAME Solar 60”
CASE-INTERNATIONAL 595 (DT) sources
- Source: Traktorenlexikon, “Case-IH 595”
- Source: Traktorenlexikon, “Case-IH 3230”