VALMET 305 (305/4) or VALMET 4100?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 305 (305/4) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4100 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The VALMET 4100 suits loader and hydraulic implement work better on this data: 59% (1,060 kg / 2,337 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 305 (305/4) | 4100 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 39 kW (52 hp)Traktorenlexikon, “Valmet 305” | 39 kW (52 hp)Traktorenlexikon, “Valmet 4100” | Not comparableNot comparable on power at the PTO shaft: the 305 (305/4) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4100 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 305 (305/4) and the 4100. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 305 (305/4) and the 4100. |
| Which pumps more oil for implements? | 35.6 L/min (9.4 gpm)Traktorenlexikon, “Valmet 305” | 39.0 L/min (10.3 gpm)Traktorenlexikon, “Valmet 4100” | EvenEven on hydraulic flow (both pump flow, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which lifts more on the three-point hitch? | 1,795 kg (3,957 lb)Traktorenlexikon, “Valmet 305” | 2,855 kg (6,294 lb)Traktorenlexikon, “Valmet 4100” | AheadThe VALMET 4100 has 59% more lift (1,060 kg / 2,337 lb) than the VALMET 305 (305/4) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,710 kg (5,975 lb)Traktorenlexikon, “Valmet 305” | 2,660 kg (5,864 lb)Traktorenlexikon, “Valmet 4100” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 305 (305/4) and the 4100. |
| Which has the wider choice of gears? | 8 to 12Traktorenlexikon, “Valmet 305” | 8 to 12Traktorenlexikon, “Valmet 4100” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 305 (305/4) and the 4100. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 305” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 4100” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Valmet 305” | 540E/540 rpmTraktorenlexikon, “Valmet 4100” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Valmet 305” | independentTraktorenlexikon, “Valmet 4100” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Valmet 305” | Two-wheel or four-wheel driveTraktorenlexikon, “Valmet 4100” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1989 | 1993–1996 | Ahead (a fact, not an advantage)The VALMET 4100 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 4100 has 59% more lift (1,060 kg / 2,337 lb) than the VALMET 305 (305/4) (both lift at the hitch ends, as stated by the source).
- The VALMET 4100 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts.
- Even on hydraulic flow (both pump flow, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 305 (305/4) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4100 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources