Steyr 1400 a or VALMET 2005-4?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 1400 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 2005-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The VALMET 2005-4 suits loader and hydraulic implement work better on this data: 53% (21.6 L/min / 5.7 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 1400 a | 2005-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 103 kW (138 hp)Traktorenlexikon, “Steyr 1400” | 103 kW (138 hp)Traktorenlexikon, “Valmet 2005” | Not comparableNot comparable on power at the PTO shaft: the 1400 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 2005-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 1400 a and the 2005-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 1400 a and the 2005-4. |
| Which pumps more oil for implements? | 41.0 L/min (10.8 gpm)Traktorenlexikon, “Steyr 1400” | 62.6 L/min (16.5 gpm)Traktorenlexikon, “Valmet 2005” | AheadThe VALMET 2005-4 has 53% more hydraulic flow (21.6 L/min / 5.7 gpm) than the Steyr 1400a (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 4,520 kg (9,965 lb)Traktorenlexikon, “Steyr 1400” | 4,720 kg (10,406 lb)Traktorenlexikon, “Valmet 2005” | EvenEven on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which is heavier, for traction? | 5,660 kg (12,478 lb)Traktorenlexikon, “Steyr 1400” | 6,335 kg (13,966 lb)Traktorenlexikon, “Valmet 2005” | Ahead (a fact, not an advantage)The VALMET 2005-4 is 12% heavier (675 kg / 1,488 lb) than the Steyr 1400a (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 8,000 kg (17,637 lb)Traktorenlexikon, “Steyr 1400” | — | No figureNo call on maximum permissible mass: no figure on record for the 2005-4. |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Steyr 1400” | 16Traktorenlexikon, “Valmet 2005” | AheadThe VALMET 2005-4 has 33% more forward gears (4 gears) than the Steyr 1400a (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 1400 a and the 2005-4. |
| Which is faster on the road? | 32 km/h (19.9 mph)Traktorenlexikon, “Steyr 1400” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 2005” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 1000 rpmTraktorenlexikon, “Steyr 1400” | 540/1000 rpmTraktorenlexikon, “Valmet 2005” | AheadThe VALMET 2005-4 offers 540 rpm at the PTO, which the Steyr 1400a does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Steyr 1400” | — | No figureNo call on PTO independence: not stated for the 2005-4. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Steyr 1400” | 4WDTraktorenlexikon, “Valmet 2005” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1974–1979 | 1986–1987 | Ahead (a fact, not an advantage)The VALMET 2005-4 is newer: production began 12 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 2005-4 has 53% more hydraulic flow (21.6 L/min / 5.7 gpm) than the Steyr 1400a (both pump flow, as stated by the source).
- The VALMET 2005-4 is 12% heavier (675 kg / 1,488 lb) than the Steyr 1400a (both unladen weight, as stated by the source).
- The VALMET 2005-4 has 33% more forward gears (4 gears) than the Steyr 1400a (both forward gears, as stated by the source).
- The VALMET 2005-4 offers 540 rpm at the PTO, which the Steyr 1400a does not (as stated by the sources).
- The VALMET 2005-4 is newer: production began 12 years later. We hold no parts-availability data, so there is no call on parts.
- Even on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 1400 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 2005-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources