12 material differences
Tractor oneSAME 35 DT1992–2003No measured PTO figureTractor twoUTB U-3601977–1991No measured PTO figure
Which should you choose?
Read our verdict on the 35 DT and the U-360 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | 35 DT | U-360 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 34.5 hp | 34.5 hp | — |
| Engine declared | MITSUBISHI K4 F-D | UTB D-115.000 | differs |
| Displacement declared | 1.49 L | 2.40 L | +61% U-360 |
| Maximum torque declared | 63 lb·ft · 84.9 N·m | 97 lb·ft · 132 N·m | +55% U-360 |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 14.3 mph · 23 km/h | +9% 35 DT |
| Clutch declared | Pedal operated dry single-plate clutch | — | — |
| Hydraulics & hitch | |||
| Hydraulic control declared | Load sensing | — | — |
| Pump flow declared | 7.9 gpm · 30.0 L/min | 5.8 gpm · 21.8 L/min | +38% 35 DT |
| Pressure declared | 1,305 psi · 90 bar | — | — |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 2,513 lb · 1,140 kg | 3,799 lb · 1,723 kg | +51% U-360 |
| Maximum permissible mass declared | 5,291 lb · 2,400 kg | — | — |
| Wheelbase declared | 64.2 in · 1,630 mm | 75.5 in · 1,918 mm | +18% U-360 |
| Length declared | 116.5 in · 2,960 mm | 113.0 in · 2,870 mm | — |
| Width declared | 48.8–52.8 in · 1,240–1,340 mm | 65.9 in · 1,674 mm | differs |
| Ground clearance declared | 13.6 in · 345 mm | 18.0 in · 457 mm | +32% U-360 |
| Turning radius, braked declared | 8.9 ft · 2.71 m | 9.7 ft · 2.95 m | +9% U-360 |
| Fuel tank declared | 30.6 qt · 29.0 L | 56.0 qt · 53.0 L | +83% U-360 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
SAME 35 DT sources
Source
- Source: Traktorenlexikon, “SAME Solaris 35”
- Source: Traktorenlexikon, “Hürlimann Prince 435”
UTB U-360 sources
Source
- Source: Traktorenlexikon, “UTB U 360”
- Source: Traktorenlexikon, “UTB U 453 DT”