12 material differences
Tractor oneSAME Delfino 35 (1981-1995)1981–1995No measured PTO figureTractor twoSOMECA 400 (DT)1968–1971No measured PTO figure
Which should you choose?
Read our verdict on the Delfino 35 (1981-1995) and the 400 (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | Delfino 35 (1981-1995) | 400 (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 34 hp | 34 hp | — |
| Engine declared | SAME DA 034-982 L | O.M.-FIAT 8035.01.201 | differs |
| Displacement declared | 1.81 L | 2.34 L | +29% 400 (DT) |
| Maximum torque declared | 90 lb·ft · 122 N·m | 103 lb·ft · 140 N·m | +15% 400 (DT) |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 15.5 mph · 25 km/h | differs |
| Clutch declared | Pedal operated dry two stage SAME double clutch | — | — |
| Hydraulics & hitch | |||
| Pump flow declared | 3.4 gpm · 13.0 L/min | 5.8 gpm · 21.8 L/min | +68% 400 (DT) |
| Pressure declared | — | 2,843 psi · 196 bar | — |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 3,086 lb · 1,400 kg | 3,748 lb · 1,700 kg | +21% 400 (DT) |
| Wheelbase declared | 66.9 in · 1,700 mm | 75.6 in · 1,920 mm | +13% 400 (DT) |
| Length declared | 116.5 in · 2,960 mm | 126.0 in · 3,200 mm | +8% 400 (DT) |
| Width declared | 58.1–81.7 in · 1,475–2,075 mm | 62.4–88.2 in · 1,585–2,240 mm | differs |
| Ground clearance declared | 13.8 in · 350 mm | 14.6 in · 370 mm | +6% 400 (DT) |
| Turning radius, braked declared | 8.7 ft · 2.65 m | 9.7 ft · 2.95 m | +11% 400 (DT) |
| Fuel tank declared | 26.4 qt · 25.0 L | 57.1 qt · 54.0 L | +116% 400 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
SAME Delfino 35 (1981-1995) sources
- Source: Traktorenlexikon, “SAME Delfino 35 (1981-1995)”
- Source: Traktorenlexikon, “SAME Delfino 35”
SOMECA 400 (DT) sources
- Source: Traktorenlexikon, “Someca 400”