9 material differences · fewer than 12
Tractor oneLandini R-8500 (DT) "TL 23 N/A"1973–1983No measured PTO figureTractor twoZETOR 8011/80451968–1987No measured PTO figure
Which should you choose?
Read our verdict on the R-8500 (DT) "TL 23 N/A" and the 8011/8045 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | R-8500 (DT) "TL 23 N/A" | 8011/8045 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 78.9 hp | 78.9 hp | — |
| Engine declared | Perkins A 4.248 | ZETOR Z-8001 | differs |
| Displacement declared | 4.07 L | 4.56 L | +12% 8011/8045 |
| Maximum torque declared | 213 lb·ft · 289 N·m | 196 lb·ft · 266 N·m | +9% R-8500 (DT) "TL 23 N/A" |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry LUK double clutch | — | — |
| Hydraulics & hitch | |||
| Pump flow declared | 7.1 gpm · 26.7 L/min | — | — |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 5,754 lb · 2,610 kg | 8,611 lb · 3,906 kg | +50% 8011/8045 |
| Wheelbase declared | 90.2 in · 2,290 mm | 92.8 in · 2,358 mm | — |
| Length declared | 148.8 in · 3,780 mm | 163.0 in · 4,140 mm | +10% 8011/8045 |
| Width declared | 73.6–98.0 in · 1,870–2,490 mm | 77.3 in · 1,964 mm | differs |
| Ground clearance declared | 20.1 in · 510 mm | 12.4 in · 315 mm | +62% R-8500 (DT) "TL 23 N/A" |
| Turning radius, braked declared | 12.0 ft · 3.65 m | 11.2 ft · 3.41 m | +7% R-8500 (DT) "TL 23 N/A" |
| Fuel tank declared | 64.5 qt · 61.0 L | 95.1 qt · 90.0 L | +48% 8011/8045 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini R-8500 (DT) "TL 23 N/A" sources
- Source: Traktorenlexikon, “Landini 8500”
- Source: Traktorenlexikon, “Massey Ferguson MF 178”
ZETOR 8011/8045 sources
- Source: Traktorenlexikon, “Zetor 8011/8045”