Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) or VOLVO-BM-VALMET Volvo 505?
Which should you choose?
On performance, every comparable figure that differs favours the VOLVO-BM-VALMET Volvo 505: hydraulic flow and three-point lift.
- The VOLVO-BM-VALMET Volvo 505 suits loader and hydraulic implement work better on this data: 42% (15.5 L/min / 4.1 gpm) more hydraulic flow and 85% (1,815 kg / 4,001 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | R-7860 (DT) TL-20 N/M (TL-20 DT/M) | Volvo 505 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 45.1 kW (60.5 hp)Traktorenlexikon, “Landini 7860” | 45.0 kW (60.3 hp)Traktorenlexikon, “Volvo 505” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the R-7860 (DT) TL-20 N/M (TL-20 DT/M) and the Volvo 505. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the R-7860 (DT) TL-20 N/M (TL-20 DT/M) and the Volvo 505. |
| Which pumps more oil for implements? | 37.2 L/min (9.8 gpm)Traktorenlexikon, “Landini 7860” | 52.7 L/min (13.9 gpm)Traktorenlexikon, “Volvo 505” | AheadThe VOLVO-BM-VALMET Volvo 505 has 42% more hydraulic flow (15.5 L/min / 4.1 gpm) than the Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,131 kg (4,698 lb)Traktorenlexikon, “Landini 7860” | 3,946 kg (8,699 lb)Traktorenlexikon, “Volvo 505” | AheadThe VOLVO-BM-VALMET Volvo 505 has 85% more lift (1,815 kg / 4,001 lb) than the Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,860 kg (6,305 lb)Traktorenlexikon, “Landini 7860” | 3,520 kg (7,760 lb)Traktorenlexikon, “Volvo 505” | Ahead (a fact, not an advantage)The VOLVO-BM-VALMET Volvo 505 is 23% heavier (660 kg / 1,455 lb) than the Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the R-7860 (DT) TL-20 N/M (TL-20 DT/M) and the Volvo 505. |
| Which has the wider choice of gears? | 12 to 24Traktorenlexikon, “Landini 7860” | 8 to 16Traktorenlexikon, “Volvo 505” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the R-7860 (DT) TL-20 N/M (TL-20 DT/M) and the Volvo 505. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 7860” | 30 km/h (18.6 mph)Traktorenlexikon, “Volvo 505” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Landini 7860” | 540/1000 rpmTraktorenlexikon, “Volvo 505” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Landini 7860” | independentTraktorenlexikon, “Volvo 505” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 7860” | 2WD / 4WDTraktorenlexikon, “Volvo 505” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1988–2000 | 1983–1985 | Ahead (a fact, not an advantage)The Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VOLVO-BM-VALMET Volvo 505 has 42% more hydraulic flow (15.5 L/min / 4.1 gpm) than the Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) (both pump flow, as stated by the source).
- The VOLVO-BM-VALMET Volvo 505 has 85% more lift (1,815 kg / 4,001 lb) than the Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) (both lift at the hitch ends, as stated by the source).
- The VOLVO-BM-VALMET Volvo 505 is 23% heavier (660 kg / 1,455 lb) than the Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) (both unladen weight, as stated by the source).
- The Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources