Landini 7800 (DT) or VALMET 565/II?
Which should you choose?
The figures split: the VALMET 565/II is ahead on hydraulic flow; the Landini 7800 (DT) is ahead on three-point lift, forward gears and PTO speeds.
- The Landini 7800 (DT) suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 7800 (DT) | 565/II | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 45.5 kW (61.0 hp)Traktorenlexikon, “Landini 7800 DT” | 45.5 kW (61.0 hp)Traktorenlexikon, “Valmet 565/II” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 7800 (DT) and the 565/II. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 7800 (DT) and the 565/II. |
| Which pumps more oil for implements? | 49.0 L/min (12.9 gpm)Traktorenlexikon, “Landini 7800 DT” | 55.0 L/min (14.5 gpm)Traktorenlexikon, “Valmet 565/II” | AheadThe VALMET 565/II has 12% more hydraulic flow (6.0 L/min / 1.6 gpm) than the Landini 7800 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,560 kg (7,848 lb)Traktorenlexikon, “Landini 7800 DT” | 2,580 kg (5,688 lb)Traktorenlexikon, “Valmet 565/II” | AheadThe Landini 7800 (DT) has 38% more lift (980 kg / 2,161 lb) than the VALMET 565/II (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,705 kg (8,168 lb)Traktorenlexikon, “Landini 7800 DT” | 3,100 kg (6,834 lb)Traktorenlexikon, “Valmet 565/II” | Ahead (a fact, not an advantage)The Landini 7800 (DT) is 20% heavier (605 kg / 1,334 lb) than the VALMET 565/II (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 7800 (DT) and the 565/II. |
| Which has the wider choice of gears? | 32Traktorenlexikon, “Landini 7800 DT” | 8 to 12Traktorenlexikon, “Valmet 565/II” | AheadThe Landini 7800 (DT) has 167% more forward gears (20 gears) than the VALMET 565/II (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 7800 (DT) and the 565/II. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 7800 DT” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Valmet 565/II” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Landini 7800 DT” | 540E/540 rpmTraktorenlexikon, “Valmet 565/II” | AheadThe Landini 7800 (DT) offers 1000 rpm at the PTO, which the VALMET 565/II does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Landini 7800 DT” | independentTraktorenlexikon, “Valmet 565/II” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Landini 7800 DT” | 4WDTraktorenlexikon, “Valmet 565/II” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1987–2000 | 1992–1997 | Ahead (a fact, not an advantage)The VALMET 565/II is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 565/II has 12% more hydraulic flow (6.0 L/min / 1.6 gpm) than the Landini 7800 (DT) (both pump flow, as stated by the source).
- The Landini 7800 (DT) has 38% more lift (980 kg / 2,161 lb) than the VALMET 565/II (both lift at the hitch ends, as stated by the source).
- The Landini 7800 (DT) is 20% heavier (605 kg / 1,334 lb) than the VALMET 565/II (both unladen weight, as stated by the source).
- The Landini 7800 (DT) has 167% more forward gears (20 gears) than the VALMET 565/II (both forward gears, as stated by the source).
- The Landini 7800 (DT) offers 1000 rpm at the PTO, which the VALMET 565/II does not (as stated by the sources).
- The VALMET 565/II is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources