John Deere 5400 (A) or Massey Ferguson MF 284 S (A)?
Which should you choose?
On performance, every comparable figure that differs favours the John Deere 5400 (A): hydraulic flow and three-point lift. It is also ahead on top speed. On features, the Massey Ferguson MF 284 S (A) is ahead on PTO speeds.
- The Massey Ferguson MF 284 S (A) suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The John Deere 5400 (A) suits loader and hydraulic implement work better on this data: 33% (11.1 L/min / 2.9 gpm) more hydraulic flow and 13% (195 kg / 431 lb) more three-point lift.
- The John Deere 5400 (A) suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 5400 (A) | MF 284 S (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 45.2 kW (60.6 hp)Traktorenlexikon, “John Deere 5400 (USA)” | 45.2 kW (60.7 hp)Traktorenlexikon, “Massey Ferguson MF 284 S” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 5400 (A) and the MF 284 S (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 5400 (A) and the MF 284 S (A). |
| Which pumps more oil for implements? | 44.7 L/min (11.8 gpm)Traktorenlexikon, “John Deere 5400 (USA)” | 33.6 L/min (8.9 gpm)Traktorenlexikon, “Massey Ferguson MF 284 S” | AheadThe John Deere 5400 (A) has 33% more hydraulic flow (11.1 L/min / 2.9 gpm) than the Massey Ferguson MF 284 S (A) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,725 kg (3,803 lb)Traktorenlexikon, “John Deere 5400 (USA)” | 1,530 kg (3,372 lb)Traktorenlexikon, “Massey Ferguson MF 284 S” | AheadThe John Deere 5400 (A) has 13% more lift (195 kg / 431 lb) than the Massey Ferguson MF 284 S (A) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,114 kg (4,661 lb)Traktorenlexikon, “John Deere 5400 (USA)” | 3,240 kg (7,143 lb)Traktorenlexikon, “Massey Ferguson MF 284 S” | Ahead (a fact, not an advantage)The Massey Ferguson MF 284 S (A) is 53% heavier (1,126 kg / 2,482 lb) than the John Deere 5400 (A) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 5400 (A) and the MF 284 S (A). |
| Which has the wider choice of gears? | 9 to 12Traktorenlexikon, “John Deere 5400 (USA)” | 12Traktorenlexikon, “Massey Ferguson MF 284 S” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 5400 (A) and the MF 284 S (A). |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “John Deere 5400 (USA)” | 25 km/h (15.5 mph)Traktorenlexikon, “Massey Ferguson MF 284 S” | AheadThe John Deere 5400 (A) has 20% more top speed (5.0 km/h / 3.1 mph) than the Massey Ferguson MF 284 S (A) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “John Deere 5400 (USA)” | 540/1000 rpmTraktorenlexikon, “Massey Ferguson MF 284 S” | AheadThe Massey Ferguson MF 284 S (A) offers 1000 rpm at the PTO, which the John Deere 5400 (A) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “John Deere 5400 (USA)” | independentTraktorenlexikon, “Massey Ferguson MF 284 S” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “John Deere 5400 (USA)” | 2WD / 4WDTraktorenlexikon, “Massey Ferguson MF 284 S” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1992–1997 | 1983–1989 | Ahead (a fact, not an advantage)The John Deere 5400 (A) is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 5400 (A) has 33% more hydraulic flow (11.1 L/min / 2.9 gpm) than the Massey Ferguson MF 284 S (A) (both pump flow, as stated by the source).
- The John Deere 5400 (A) has 13% more lift (195 kg / 431 lb) than the Massey Ferguson MF 284 S (A) (both lift at the hitch ends, as stated by the source).
- The Massey Ferguson MF 284 S (A) is 53% heavier (1,126 kg / 2,482 lb) than the John Deere 5400 (A) (both unladen weight, as stated by the source).
- The John Deere 5400 (A) has 20% more top speed (5.0 km/h / 3.1 mph) than the Massey Ferguson MF 284 S (A) (both top speed forward, as stated by the source).
- The Massey Ferguson MF 284 S (A) offers 1000 rpm at the PTO, which the John Deere 5400 (A) does not (as stated by the sources).
- The John Deere 5400 (A) is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources