International Harvester 745 XL(A) or Landini 7830 (DT) TL-20 N/F (TL-20 DT/F)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 745 XL(A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 7830 (DT) TL-20 N/F (TL-20 DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) suits loader and hydraulic implement work better on this data: 25% (7.7 L/min / 2.0 gpm) more hydraulic flow.
- The International Harvester 745 XL(A) suits road haulage better on this data: 33% (10.0 km/h / 6.2 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 745 XL(A) | 7830 (DT) TL-20 N/F (TL-20 DT/F) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 52.7 kW (70.7 hp)Traktorenlexikon, “IHC 745XL” | 53 kW (71 hp)Traktorenlexikon, “Landini 7830 (DT)” | Not comparableNot comparable on power at the PTO shaft: the 745 XL(A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 7830 (DT) TL-20 N/F (TL-20 DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 745 XL(A) and the 7830 (DT) TL-20 N/F (TL-20 DT/F). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 745 XL(A) and the 7830 (DT) TL-20 N/F (TL-20 DT/F). |
| Which pumps more oil for implements? | 31.0 L/min (8.2 gpm)Traktorenlexikon, “IHC 745XL” | 38.7 L/min (10.2 gpm)Traktorenlexikon, “Landini 7830 (DT)” | AheadThe Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) has 25% more hydraulic flow (7.7 L/min / 2.0 gpm) than the International Harvester 745 XL(A) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,151 kg (6,947 lb)Traktorenlexikon, “IHC 745XL” | 3,050 kg (6,724 lb)Traktorenlexikon, “Landini 7830 (DT)” | EvenEven on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which is heavier, for traction? | 3,430 kg (7,562 lb)Traktorenlexikon, “IHC 745XL” | 2,715 kg (5,986 lb)Traktorenlexikon, “Landini 7830 (DT)” | Ahead (a fact, not an advantage)The International Harvester 745 XL(A) is 26% heavier (715 kg / 1,576 lb) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 5,500 kg (12,125 lb)Traktorenlexikon, “IHC 745XL” | — | No figureNo call on maximum permissible mass: no figure on record for the 7830 (DT) TL-20 N/F (TL-20 DT/F). |
| Which has the wider choice of gears? | 16Traktorenlexikon, “IHC 745XL” | 12Traktorenlexikon, “Landini 7830 (DT)” | AheadThe International Harvester 745 XL(A) has 33% more forward gears (4 gears) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 745 XL(A) and the 7830 (DT) TL-20 N/F (TL-20 DT/F). |
| Which is faster on the road? | 40 km/h (24.9 mph)Traktorenlexikon, “IHC 745XL” | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 7830 (DT)” | AheadThe International Harvester 745 XL(A) has 33% more top speed (10.0 km/h / 6.2 mph) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpm / 1000 rpmTraktorenlexikon, “IHC 745XL” | 540/1000 rpmTraktorenlexikon, “Landini 7830 (DT)” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “IHC 745XL” | — | No figureNo call on PTO independence: not stated for the 7830 (DT) TL-20 N/F (TL-20 DT/F). |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “IHC 745XL” | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 7830 (DT)” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1981–1990 | 1983–1987 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) has 25% more hydraulic flow (7.7 L/min / 2.0 gpm) than the International Harvester 745 XL(A) (both pump flow, as stated by the source).
- The International Harvester 745 XL(A) is 26% heavier (715 kg / 1,576 lb) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both unladen weight, as stated by the source).
- The International Harvester 745 XL(A) has 33% more forward gears (4 gears) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both forward gears, as stated by the source).
- The International Harvester 745 XL(A) has 33% more top speed (10.0 km/h / 6.2 mph) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both top speed forward, as stated by the source).
- Even on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 745 XL(A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 7830 (DT) TL-20 N/F (TL-20 DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources