International Harvester D-436 or UTB 445 DTC?
Which should you choose?
On performance, every comparable figure that differs favours the International Harvester D-436: hydraulic flow. On features, the UTB 445 DTC is ahead on top speed and drive.
- The International Harvester D-436 suits loader and hydraulic implement work better on this data: 10% (2.2 L/min / 0.6 gpm) more hydraulic flow.
- The UTB 445 DTC suits heavy draft work (ploughing, cultivating) better on this data: 26% (452 kg / 996 lb) heavier and four-wheel drive.
- The UTB 445 DTC suits road haulage better on this data: 25% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D-436 | 445 DTC | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 27.1 kW (36.4 hp)Traktorenlexikon, “McCormick D-436 Standard” | 27.2 kW (36.5 hp)Traktorenlexikon, “UTB U 445 DT” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D-436 and the 445 DTC. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D-436 and the 445 DTC. |
| Which pumps more oil for implements? | 24.0 L/min (6.3 gpm)Traktorenlexikon, “McCormick D-436 Standard” | 21.8 L/min (5.8 gpm)Traktorenlexikon, “UTB U 445 DT” | AheadThe International Harvester D-436 has 10% more hydraulic flow (2.2 L/min / 0.6 gpm) than the UTB 445 DTC (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 1,450 kg (3,197 lb)Traktorenlexikon, “UTB U 445 DT” | No figureNo call on three-point lift: no figure on record for the D-436. |
| Which is heavier, for traction? | 1,748 kg (3,854 lb)Traktorenlexikon, “McCormick D-436 Standard” | 2,200 kg (4,850 lb)Traktorenlexikon, “UTB U 445 DT” | Ahead (a fact, not an advantage)The UTB 445 DTC is 26% heavier (452 kg / 996 lb) than the International Harvester D-436 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the D-436 and the 445 DTC. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “McCormick D-436 Standard” | 6 to 9Traktorenlexikon, “UTB U 445 DT” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D-436 and the 445 DTC. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “McCormick D-436 Standard” | 25 km/h (15.5 mph)Traktorenlexikon, “UTB U 445 DT” | AheadThe UTB 445 DTC has 25% more top speed (5.0 km/h / 3.1 mph) than the International Harvester D-436 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “McCormick D-436 Standard” | 540 rpmTraktorenlexikon, “UTB U 445 DT” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “McCormick D-436 Standard” | — | No figureNo call on PTO independence: not stated for the 445 DTC. |
| Which drives on both axles? | 2WDTraktorenlexikon, “McCormick D-436 Standard” | 4WDTraktorenlexikon, “UTB U 445 DT” | AheadThe UTB 445 DTC is available with four-wheel drive; the International Harvester D-436 is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1959–1962 | 1974–1981 | Ahead (a fact, not an advantage)The UTB 445 DTC is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The International Harvester D-436 has 10% more hydraulic flow (2.2 L/min / 0.6 gpm) than the UTB 445 DTC (both pump flow, as stated by the source).
- The UTB 445 DTC is 26% heavier (452 kg / 996 lb) than the International Harvester D-436 (both unladen weight, as stated by the source).
- The UTB 445 DTC has 25% more top speed (5.0 km/h / 3.1 mph) than the International Harvester D-436 (both top speed forward, as stated by the source).
- The UTB 445 DTC is available with four-wheel drive; the International Harvester D-436 is two-wheel drive (as stated by the sources).
- The UTB 445 DTC is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540 rpm).
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources