International Harvester D-432 or John Deere 820?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the D-432 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 820 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D-432 | 820 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 23.5 kW (31.5 hp)Traktorenlexikon, “McCormick D-432” | 23.5 kW (31.5 hp)Traktorenlexikon, “John Deere 820” | Not comparableNot comparable on power at the PTO shaft: the D-432 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 820 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D-432 and the 820. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D-432 and the 820. |
| Which pumps more oil for implements? | 15.5 L/min (4.1 gpm)Traktorenlexikon, “McCormick D-432” | 26.0 L/min (6.9 gpm)Traktorenlexikon, “John Deere 820” | AheadThe John Deere 820 has 68% more hydraulic flow (10.5 L/min / 2.8 gpm) than the International Harvester D-432 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,500 kg (3,307 lb)Traktorenlexikon, “McCormick D-432” | 1,245 kg (2,745 lb)Traktorenlexikon, “John Deere 820” | AheadThe International Harvester D-432 has 20% more lift (255 kg / 562 lb) than the John Deere 820 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 1,494 kg (3,294 lb)Traktorenlexikon, “McCormick D-432” | 2,150 kg (4,740 lb)Traktorenlexikon, “John Deere 820” | Ahead (a fact, not an advantage)The John Deere 820 is 44% heavier (656 kg / 1,446 lb) than the International Harvester D-432 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | 3,500 kg (7,716 lb)Traktorenlexikon, “John Deere 820” | No figureNo call on maximum permissible mass: no figure on record for the D-432. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “McCormick D-432” | 7Traktorenlexikon, “John Deere 820” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D-432 and the 820. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “McCormick D-432” | 20 km/h (12.4 mph) to 25 km/h (15.5 mph)Traktorenlexikon, “John Deere 820” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “McCormick D-432” | 540/1000 rpmTraktorenlexikon, “John Deere 820” | AheadThe John Deere 820 offers 1000 rpm at the PTO, which the International Harvester D-432 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “McCormick D-432” | independentTraktorenlexikon, “John Deere 820” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WDTraktorenlexikon, “McCormick D-432” | 2WDTraktorenlexikon, “John Deere 820” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1962–1966 | 1967–1975 | Ahead (a fact, not an advantage)The John Deere 820 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 820 has 68% more hydraulic flow (10.5 L/min / 2.8 gpm) than the International Harvester D-432 (both pump flow, as stated by the source).
- The International Harvester D-432 has 20% more lift (255 kg / 562 lb) than the John Deere 820 (both lift at the hitch ends, as stated by the source).
- The John Deere 820 is 44% heavier (656 kg / 1,446 lb) than the International Harvester D-432 (both unladen weight, as stated by the source).
- The John Deere 820 offers 1000 rpm at the PTO, which the International Harvester D-432 does not (as stated by the sources).
- The John Deere 820 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: all two-wheel drive.
- Not comparable on power at the PTO shaft: the D-432 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 820 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources