International Harvester 444 USA or John Deere 60?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 444 USA has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 60 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The John Deere 60 suits loader and hydraulic implement work better on this data: 50% (11.2 L/min / 3.0 gpm) more hydraulic flow.
- The International Harvester 444 USA suits road haulage better on this data: 41% (7.3 km/h / 4.5 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 444 USA | 60 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 27.1 kW (36.3 hp)Traktorenlexikon, “IHC 444 USA” | 27.5 kW (36.9 hp)Traktorenlexikon, “John Deere Modell 60” | Not comparableNot comparable on power at the PTO shaft: the 444 USA has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 60 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 444 USA and the 60. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 444 USA and the 60. |
| Which pumps more oil for implements? | 22.5 L/min (5.9 gpm)Traktorenlexikon, “IHC 444 USA” | 33.7 L/min (8.9 gpm)Traktorenlexikon, “John Deere Modell 60” | AheadThe John Deere 60 has 50% more hydraulic flow (11.2 L/min / 3.0 gpm) than the International Harvester 444 USA (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | — | No figureNo call on three-point lift: no figure on record for the 444 USA and the 60. |
| Which is heavier, for traction? | 1,846 kg (4,070 lb)Traktorenlexikon, “IHC 444 USA” | 2,680 kg (5,908 lb)Traktorenlexikon, “John Deere Modell 60” | Ahead (a fact, not an advantage)The John Deere 60 is 45% heavier (834 kg / 1,839 lb) than the International Harvester 444 USA (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 444 USA and the 60. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “IHC 444 USA” | 6Traktorenlexikon, “John Deere Modell 60” | AheadThe International Harvester 444 USA has 33% more forward gears (2 gears) than the John Deere 60 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 444 USA and the 60. |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “IHC 444 USA” | 17.7 km/h (11.0 mph)Traktorenlexikon, “John Deere Modell 60” | AheadThe International Harvester 444 USA has 41% more top speed (7.3 km/h / 4.5 mph) than the John Deere 60 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “IHC 444 USA” | 536 rpmTraktorenlexikon, “John Deere Modell 60” | No figureNo call on PTO speeds: no standard PTO speed stated for the 60. |
| Which PTO runs independently of the ground drive? | dependent (stops with the clutch)Traktorenlexikon, “IHC 444 USA” | — | No figureNo call on PTO independence: not stated for the 60. |
| Which drives on both axles? | 2WDTraktorenlexikon, “IHC 444 USA” | 2WDTraktorenlexikon, “John Deere Modell 60” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1967–1971 | 1952–1957 | Ahead (a fact, not an advantage)The International Harvester 444 USA is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 60 has 50% more hydraulic flow (11.2 L/min / 3.0 gpm) than the International Harvester 444 USA (both pump flow, as stated by the source).
- The John Deere 60 is 45% heavier (834 kg / 1,839 lb) than the International Harvester 444 USA (both unladen weight, as stated by the source).
- The International Harvester 444 USA has 33% more forward gears (2 gears) than the John Deere 60 (both forward gears, as stated by the source).
- The International Harvester 444 USA has 41% more top speed (7.3 km/h / 4.5 mph) than the John Deere 60 (both top speed forward, as stated by the source).
- The International Harvester 444 USA is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts.
- Even on drive: all two-wheel drive.
- Not comparable on power at the PTO shaft: the 444 USA has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 60 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources