IMT 588 or Nuffield 10/60?
Which should you choose?
On performance, every comparable figure that differs favours the Nuffield 10/60: hydraulic flow. It is also ahead on forward gears and top speed.
- The Nuffield 10/60 suits loader and hydraulic implement work better on this data: 132% (19.9 L/min / 5.3 gpm) more hydraulic flow.
- The Nuffield 10/60 suits road haulage better on this data: 14% (3.0 km/h / 1.9 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 588 | 10/60 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 32.2 kW (43.2 hp)Traktorenlexikon, “IMT 558” | 32.2 kW (43.2 hp)Traktorenlexikon, “Nuffield 10/60 (1964-1967)” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 588 and the 10/60. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 588 and the 10/60. |
| Which pumps more oil for implements? | 15.1 L/min (4.0 gpm)Traktorenlexikon, “IMT 558” | 35.0 L/min (9.2 gpm)Traktorenlexikon, “Nuffield 10/60 (1964-1967)” | AheadThe Nuffield 10/60 has 132% more hydraulic flow (19.9 L/min / 5.3 gpm) than the IMT 588 (also listed as 558) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,120 kg (2,469 lb)Traktorenlexikon, “IMT 558” | — | No figureNo call on three-point lift: no figure on record for the 10/60. |
| Which is heavier, for traction? | 2,300 kg (5,071 lb)Traktorenlexikon, “IMT 558” | 2,660 kg (5,864 lb)Traktorenlexikon, “Nuffield 10/60 (1964-1967)” | Ahead (a fact, not an advantage)The Nuffield 10/60 is 16% heavier (360 kg / 794 lb) than the IMT 588 (also listed as 558) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 588 and the 10/60. |
| Which has the wider choice of gears? | 6Traktorenlexikon, “IMT 558” | 10Traktorenlexikon, “Nuffield 10/60 (1964-1967)” | AheadThe Nuffield 10/60 has 67% more forward gears (4 gears) than the IMT 588 (also listed as 558) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 588 and the 10/60. |
| Which is faster on the road? | 22 km/h (13.7 mph)Traktorenlexikon, “IMT 558” | 25 km/h (15.5 mph)Traktorenlexikon, “Nuffield 10/60 (1964-1967)” | AheadThe Nuffield 10/60 has 14% more top speed (3.0 km/h / 1.9 mph) than the IMT 588 (also listed as 558) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “IMT 558” | 540 rpmTraktorenlexikon, “Nuffield 10/60 (1964-1967)” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 588 and the 10/60. |
| Which drives on both axles? | 2WDTraktorenlexikon, “IMT 558” | 2WDTraktorenlexikon, “Nuffield 10/60 (1964-1967)” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1970–1980 | 1964–1967 | Ahead (a fact, not an advantage)The IMT 588 (also listed as 558) is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Nuffield 10/60 has 132% more hydraulic flow (19.9 L/min / 5.3 gpm) than the IMT 588 (also listed as 558) (both pump flow, as stated by the source).
- The Nuffield 10/60 is 16% heavier (360 kg / 794 lb) than the IMT 588 (also listed as 558) (both unladen weight, as stated by the source).
- The Nuffield 10/60 has 67% more forward gears (4 gears) than the IMT 588 (also listed as 558) (both forward gears, as stated by the source).
- The Nuffield 10/60 has 14% more top speed (3.0 km/h / 1.9 mph) than the IMT 588 (also listed as 558) (both top speed forward, as stated by the source).
- The IMT 588 (also listed as 558) is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on PTO speeds: the same speeds (540 rpm).
- Even on drive: all two-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources