Hürlimann 908 XT or VALMET 6300-4?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 908 XT has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 6300-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The VALMET 6300-4 suits loader and hydraulic implement work better on this data: 48% (22.5 L/min / 5.9 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 908 XT | 6300-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 62.5 kW (83.8 hp)Traktorenlexikon, “Hürlimann XT 908” | 62.5 kW (83.8 hp)Traktorenlexikon, “Valmet 6300” | Not comparableNot comparable on power at the PTO shaft: the 908 XT has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 6300-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 908 XT and the 6300-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 908 XT and the 6300-4. |
| Which pumps more oil for implements? | 47.0 L/min (12.4 gpm)Traktorenlexikon, “Hürlimann XT 908” | 69.5 L/min (18.4 gpm)Traktorenlexikon, “Valmet 6300” | AheadThe VALMET 6300-4 has 48% more hydraulic flow (22.5 L/min / 5.9 gpm) than the Hürlimann 908 XT (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,386 kg (5,261 lb)Traktorenlexikon, “Hürlimann XT 908” | 4,355 kg (9,601 lb)Traktorenlexikon, “Valmet 6300” | Not comparableNot comparable on three-point lift: the 908 XT: lift through the full range at an unstated point, as stated by the source (Traktorenlexikon, “Hürlimann XT 908”); the 6300-4: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Valmet 6300”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 4,150 kg (9,149 lb)Traktorenlexikon, “Hürlimann XT 908” | 4,070 kg (8,973 lb)Traktorenlexikon, “Valmet 6300” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | 6,500 kg (14,330 lb)Traktorenlexikon, “Valmet 6300” | No figureNo call on maximum permissible mass: no figure on record for the 908 XT. |
| Which has the wider choice of gears? | 40 to 60Traktorenlexikon, “Hürlimann XT 908” | 12 to 36Traktorenlexikon, “Valmet 6300” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 908 XT and the 6300-4. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Hürlimann XT 908” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Valmet 6300” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000/540E/1000E rpmTraktorenlexikon, “Hürlimann XT 908” | 540/1000 rpmTraktorenlexikon, “Valmet 6300” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 908 XT and the 6300-4. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Hürlimann XT 908” | 4WDTraktorenlexikon, “Valmet 6300” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1995–2004 | 1991–2007 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 6300-4 has 48% more hydraulic flow (22.5 L/min / 5.9 gpm) than the Hürlimann 908 XT (both pump flow, as stated by the source).
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 908 XT has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 6300-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the 908 XT: lift through the full range at an unstated point, as stated by the source (Traktorenlexikon, “Hürlimann XT 908”); the 6300-4: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Valmet 6300”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources