Güldner AF 30 P or Lanz D 8539?
Which should you choose?
On performance, no comparable figure differs by more than its threshold: on this data the machines are level.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | AF 30 P | D 8539 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 20.6 kW (28 hp)Traktorenlexikon, “Güldner AF 30P” | 22.1 kW (30 hp)Traktorenlexikon, “Lanz D 8539” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the AF 30 P and the D 8539. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the AF 30 P and the D 8539. |
| Which pumps more oil for implements? | — | — | No figureNo call on hydraulic flow: no figure on record for the AF 30 P and the D 8539. |
| Which lifts more on the three-point hitch? | — | — | No figureNo call on three-point lift: no figure on record for the AF 30 P and the D 8539. |
| Which is heavier, for traction? | 2,040 kg (4,497 lb)Traktorenlexikon, “Güldner AF 30P” | 4,150 kg (9,149 lb)Traktorenlexikon, “Lanz D 8539” | Ahead (a fact, not an advantage)The Lanz D 8539 is 103% heavier (2,110 kg / 4,652 lb) than the Güldner AF 30 P (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the AF 30 P and the D 8539. |
| Which has the wider choice of gears? | 5Traktorenlexikon, “Güldner AF 30P” | 6Traktorenlexikon, “Lanz D 8539” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the AF 30 P and the D 8539. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “Güldner AF 30P” | 21.5 km/h (13.4 mph)Traktorenlexikon, “Lanz D 8539” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Güldner AF 30P” | — | No figureNo call on PTO speeds: no standard PTO speed stated for the D 8539. |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the AF 30 P and the D 8539. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Güldner AF 30P” | 2WDTraktorenlexikon, “Lanz D 8539” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1948–1951 | 1934–1939 | Ahead (a fact, not an advantage)The Güldner AF 30 P is newer: production began 14 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Lanz D 8539 is 103% heavier (2,110 kg / 4,652 lb) than the Güldner AF 30 P (both unladen weight, as stated by the source).
- The Güldner AF 30 P is newer: production began 14 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on drive: all two-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, three-point lift, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources