Ford 876 or International Harvester 4786?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 876 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4786 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Ford 876 suits loader and hydraulic implement work better on this data: 33% (23.5 L/min / 6.2 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 876 | 4786 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 208.9 kW (280.1 hp)Traktorenlexikon, “Ford Ford 876” | 192.7 kW (258.4 hp)Traktorenlexikon, “IHC 4786” | Not comparableNot comparable on power at the PTO shaft: the 876 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4786 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 876 and the 4786. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 876 and the 4786. |
| Which pumps more oil for implements? | 95.4 L/min (25.2 gpm)Traktorenlexikon, “Ford Ford 876” | 71.9 L/min (19.0 gpm)Traktorenlexikon, “IHC 4786” | AheadThe Ford 876 has 33% more hydraulic flow (23.5 L/min / 6.2 gpm) than the International Harvester 4786 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | — | No figureNo call on three-point lift: no figure on record for the 876 and the 4786. |
| Which is heavier, for traction? | 12,727 kg (28,058 lb)Traktorenlexikon, “Ford Ford 876” | 13,699 kg (30,201 lb)Traktorenlexikon, “IHC 4786” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 13,400 kg (29,542 lb)Traktorenlexikon, “Ford Ford 876” | — | No figureNo call on maximum permissible mass: no figure on record for the 4786. |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Ford Ford 876” | 10Traktorenlexikon, “IHC 4786” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 876 and the 4786. |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Ford Ford 876” | 25 km/h (15.5 mph)Traktorenlexikon, “IHC 4786” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 1000 rpmTraktorenlexikon, “Ford Ford 876” | 1000 rpmTraktorenlexikon, “IHC 4786” | EvenEven on PTO speeds: the same speeds (1000 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 876 and the 4786. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Ford Ford 876” | 4WDTraktorenlexikon, “IHC 4786” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1988–1993 | 1978–1981 | Ahead (a fact, not an advantage)The Ford 876 is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Ford 876 has 33% more hydraulic flow (23.5 L/min / 6.2 gpm) than the International Harvester 4786 (both pump flow, as stated by the source).
- The Ford 876 is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 876 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4786 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources