Ford 7610 (A) or VALMET 805/805-4?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 7610 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 805/805-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The VALMET 805/805-4 suits loader and hydraulic implement work better on this data: 37% (13.7 L/min / 3.6 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 7610 (A) | 805/805-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 69.9 kW (93.7 hp)Traktorenlexikon, “Ford 7610” | 69.9 kW (93.7 hp)Traktorenlexikon, “Valmet 805” | Not comparableNot comparable on power at the PTO shaft: the 7610 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 805/805-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 7610 (A) and the 805/805-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 7610 (A) and the 805/805-4. |
| Which pumps more oil for implements? | 37.5 L/min (9.9 gpm)Traktorenlexikon, “Ford 7610” | 51.2 L/min (13.5 gpm)Traktorenlexikon, “Valmet 805” | AheadThe VALMET 805/805-4 has 37% more hydraulic flow (13.7 L/min / 3.6 gpm) than the Ford 7610 (A) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 4,255 kg (9,381 lb)Traktorenlexikon, “Ford 7610” | 4,150 kg (9,149 lb)Traktorenlexikon, “Valmet 805” | EvenEven on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which is heavier, for traction? | 2,864 kg (6,314 lb)Traktorenlexikon, “Ford 7610” | 3,540 kg (7,804 lb)Traktorenlexikon, “Valmet 805” | Ahead (a fact, not an advantage)The VALMET 805/805-4 is 24% heavier (676 kg / 1,490 lb) than the Ford 7610 (A) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 7610 (A) and the 805/805-4. |
| Which has the wider choice of gears? | 16Traktorenlexikon, “Ford 7610” | 8 to 16Traktorenlexikon, “Valmet 805” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 7610 (A) and the 805/805-4. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Ford 7610” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 805” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Ford 7610” | 540 rpmTraktorenlexikon, “Valmet 805” | AheadThe Ford 7610 (A) offers 1000 rpm at the PTO, which the VALMET 805/805-4 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Ford 7610” | independentTraktorenlexikon, “Valmet 805” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Ford 7610” | 2WD / 4WDTraktorenlexikon, “Valmet 805” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1981–1991 | 1983–1989 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 805/805-4 has 37% more hydraulic flow (13.7 L/min / 3.6 gpm) than the Ford 7610 (A) (both pump flow, as stated by the source).
- The VALMET 805/805-4 is 24% heavier (676 kg / 1,490 lb) than the Ford 7610 (A) (both unladen weight, as stated by the source).
- The Ford 7610 (A) offers 1000 rpm at the PTO, which the VALMET 805/805-4 does not (as stated by the sources).
- Even on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 7610 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 805/805-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources