Ford 1920 (A) or UTB 302 Dtce-IF?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 1920 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 302 Dtce-IF has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Ford 1920 (A) suits loader and hydraulic implement work better on this data: 20% (5.0 L/min / 1.3 gpm) more hydraulic flow.
- The UTB 302 Dtce-IF suits heavy draft work (ploughing, cultivating) better on this data: 115% (1,485 kg / 3,274 lb) heavier and four-wheel drive.
- The UTB 302 Dtce-IF suits road haulage better on this data: 14% (3.0 km/h / 1.9 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 1920 (A) | 302 Dtce-IF | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 23.5 kW (31.5 hp)Traktorenlexikon, “Ford 1920” | 22.1 kW (29.6 hp)Traktorenlexikon, “UTB U 302 DTCE IF” | Not comparableNot comparable on power at the PTO shaft: the 1920 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 302 Dtce-IF has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 1920 (A) and the 302 Dtce-IF. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 1920 (A) and the 302 Dtce-IF. |
| Which pumps more oil for implements? | 30.0 L/min (7.9 gpm)Traktorenlexikon, “Ford 1920” | 25.0 L/min (6.6 gpm)Traktorenlexikon, “UTB U 302 DTCE IF” | AheadThe Ford 1920 (A) has 20% more hydraulic flow (5.0 L/min / 1.3 gpm) than the UTB 302 Dtce-IF (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,165 kg (2,568 lb)Traktorenlexikon, “Ford 1920” | 1,200 kg (2,646 lb)Traktorenlexikon, “UTB U 302 DTCE IF” | EvenEven on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which is heavier, for traction? | 1,290 kg (2,844 lb)Traktorenlexikon, “Ford 1920” | 2,775 kg (6,118 lb)Traktorenlexikon, “UTB U 302 DTCE IF” | Ahead (a fact, not an advantage)The UTB 302 Dtce-IF is 115% heavier (1,485 kg / 3,274 lb) than the Ford 1920 (A) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 1920 (A) and the 302 Dtce-IF. |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Ford 1920” | 6Traktorenlexikon, “UTB U 302 DTCE IF” | AheadThe Ford 1920 (A) has 100% more forward gears (6 gears) than the UTB 302 Dtce-IF (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 1920 (A) and the 302 Dtce-IF. |
| Which is faster on the road? | 22 km/h (13.7 mph)Traktorenlexikon, “Ford 1920” | 25 km/h (15.5 mph)Traktorenlexikon, “UTB U 302 DTCE IF” | AheadThe UTB 302 Dtce-IF has 14% more top speed (3.0 km/h / 1.9 mph) than the Ford 1920 (A) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Ford 1920” | 540 rpmTraktorenlexikon, “UTB U 302 DTCE IF” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Ford 1920” | — | No figureNo call on PTO independence: not stated for the 302 Dtce-IF. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Ford 1920” | 4WDTraktorenlexikon, “UTB U 302 DTCE IF” | AheadThe UTB 302 Dtce-IF is available with four-wheel drive; the Ford 1920 (A) is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1987–2000 | 1980–1991 | Ahead (a fact, not an advantage)The Ford 1920 (A) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Ford 1920 (A) has 20% more hydraulic flow (5.0 L/min / 1.3 gpm) than the UTB 302 Dtce-IF (both pump flow, as stated by the source).
- The UTB 302 Dtce-IF is 115% heavier (1,485 kg / 3,274 lb) than the Ford 1920 (A) (both unladen weight, as stated by the source).
- The Ford 1920 (A) has 100% more forward gears (6 gears) than the UTB 302 Dtce-IF (both forward gears, as stated by the source).
- The UTB 302 Dtce-IF has 14% more top speed (3.0 km/h / 1.9 mph) than the Ford 1920 (A) (both top speed forward, as stated by the source).
- The UTB 302 Dtce-IF is available with four-wheel drive; the Ford 1920 (A) is two-wheel drive (as stated by the sources).
- The Ford 1920 (A) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts.
- Even on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540 rpm).
- Not comparable on power at the PTO shaft: the 1920 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 302 Dtce-IF has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources