Fiat 940 (DT) or John Deere 3050 (A)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 940 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 3050 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The John Deere 3050 (A) suits loader and hydraulic implement work better on this data: 38% (14.3 L/min / 3.8 gpm) more hydraulic flow and 19% (726 kg / 1,601 lb) more three-point lift.
- The John Deere 3050 (A) suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 940 (DT) | 3050 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 67.7 kW (90.8 hp)Traktorenlexikon, “Fiat 940/940 DT” | 67.7 kW (90.8 hp)Traktorenlexikon, “John Deere 3050” | Not comparableNot comparable on power at the PTO shaft: the 940 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 3050 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 940 (DT) and the 3050 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 940 (DT) and the 3050 (A). |
| Which pumps more oil for implements? | 38.0 L/min (10.0 gpm)Traktorenlexikon, “Fiat 940/940 DT” | 52.3 L/min (13.8 gpm)Traktorenlexikon, “John Deere 3050” | AheadThe John Deere 3050 (A) has 38% more hydraulic flow (14.3 L/min / 3.8 gpm) than the Fiat 940 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,800 kg (8,378 lb)Traktorenlexikon, “Fiat 940/940 DT” | 4,526 kg (9,978 lb)Traktorenlexikon, “John Deere 3050” | AheadThe John Deere 3050 (A) has 19% more lift (726 kg / 1,601 lb) than the Fiat 940 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,950 kg (8,708 lb)Traktorenlexikon, “Fiat 940/940 DT” | 3,920 kg (8,642 lb)Traktorenlexikon, “John Deere 3050” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | 6,700 kg (14,771 lb)Traktorenlexikon, “John Deere 3050” | No figureNo call on maximum permissible mass: no figure on record for the 940 (DT). |
| Which has the wider choice of gears? | 12 to 16Traktorenlexikon, “Fiat 940/940 DT” | 8 to 16Traktorenlexikon, “John Deere 3050” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 940 (DT) and the 3050 (A). |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Fiat 940/940 DT” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “John Deere 3050” | AheadThe John Deere 3050 (A) has 20% more top speed (5.0 km/h / 3.1 mph) than the Fiat 940 (DT) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | — | 540/1000 rpmTraktorenlexikon, “John Deere 3050” | No figureNo call on PTO speeds: no standard PTO speed stated for the 940 (DT). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “John Deere 3050” | No figureNo call on PTO independence: not stated for the 940 (DT). |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 940/940 DT” | Two-wheel or four-wheel driveTraktorenlexikon, “John Deere 3050” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1978–1979 | 1986–1993 | Ahead (a fact, not an advantage)The John Deere 3050 (A) is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 3050 (A) has 38% more hydraulic flow (14.3 L/min / 3.8 gpm) than the Fiat 940 (DT) (both pump flow, as stated by the source).
- The John Deere 3050 (A) has 19% more lift (726 kg / 1,601 lb) than the Fiat 940 (DT) (both lift at the hitch ends, as stated by the source).
- The John Deere 3050 (A) has 20% more top speed (5.0 km/h / 3.1 mph) than the Fiat 940 (DT) (both top speed forward, as stated by the source).
- The John Deere 3050 (A) is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 940 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 3050 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources