9 material differences · fewer than 12
Tractor oneFiat 600 (DT)1971–1973No measured PTO figureTractor twoSOMECA 715 (DT)1966–1967No measured PTO figure
Which should you choose?
We will not advise between these two machines, because their unladen weight differs by more than 25% (28%); they were not built in overlapping years (1971–1973; 1966–1967). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
9 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | 600 (DT) | 715 (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 59.3 hp | 59.3 hp | — |
| Engine declared | Fiat 8045.02 | O.M.-FIAT CO-2 D/70 | differs |
| Displacement declared | 3.46 L | — | — |
| Maximum torque declared | 147 lb·ft · 199 N·m | 192 lb·ft · 260 N·m | +31% 715 (DT) |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 15.5 mph · 25 km/h | — |
| Clutch declared | — | Pedal-operated two-stage dry FERODO double clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | 5.8 gpm · 21.8 L/min | 7.0 gpm · 26.5 L/min | +22% 715 (DT) |
| Pressure declared | 2,901 psi · 200 bar | 2,843 psi · 196 bar | — |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 4,960 lb · 2,250 kg | 6,349 lb · 2,880 kg | +28% 715 (DT) |
| Wheelbase declared | 81.5 in · 2,070 mm | 86.6 in · 2,200 mm | +6% 715 (DT) |
| Length declared | 133.9 in · 3,400 mm | 149.6 in · 3,800 mm | +12% 715 (DT) |
| Width declared | 68.1–95.7 in · 1,730–2,430 mm | 70.9 in · 1,800 mm | differs |
| Ground clearance declared | 17.7 in · 450 mm | 18.3 in · 465 mm | — |
| Turning radius, braked declared | 10.7 ft · 3.25 m | 12.5 ft · 3.80 m | +17% 715 (DT) |
| Fuel tank declared | 57.1 qt · 54.0 L | 88.8 qt · 84.0 L | +56% 715 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Fiat 600 (DT) sources
- Source: Traktorenlexikon, “Fiat 600N/600 DT”
SOMECA 715 (DT) sources
- Source: Traktorenlexikon, “Someca 715”
- Source: Traktorenlexikon, “Fiat 715/715 DT”