Fiat 55-66 V/F (DT-V/F) or Hürlimann H-356 (A)?
Which should you choose?
On performance, no comparable figure differs by more than its threshold: on this data the machines are level.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 55-66 V/F (DT-V/F) | H-356 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 33.4 kW (44.8 hp)Traktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | 33.4 kW (44.8 hp)Traktorenlexikon, “Hürlimann H 356” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 55-66 V/F (DT-V/F) and the H-356 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 55-66 V/F (DT-V/F) and the H-356 (A). |
| Which pumps more oil for implements? | — | 31.6 L/min (8.3 gpm)Traktorenlexikon, “Hürlimann H 356” | No figureNo call on hydraulic flow: no figure on record for the 55-66 V/F (DT-V/F). |
| Which lifts more on the three-point hitch? | 2,600 kg (5,732 lb)Traktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | — | No figureNo call on three-point lift: no figure on record for the H-356 (A). |
| Which is heavier, for traction? | 1,540 kg (3,395 lb)Traktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | 2,460 kg (5,423 lb)Traktorenlexikon, “Hürlimann H 356” | Ahead (a fact, not an advantage)The Hürlimann H-356 (A) is 60% heavier (920 kg / 2,028 lb) than the Fiat 55-66 V/F (DT-V/F) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 55-66 V/F (DT-V/F) and the H-356 (A). |
| Which has the wider choice of gears? | 12 to 20Traktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | 15 to 24Traktorenlexikon, “Hürlimann H 356” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 55-66 V/F (DT-V/F) and the H-356 (A). |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | 30 km/h (18.6 mph)Traktorenlexikon, “Hürlimann H 356” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | 540/1000 rpmTraktorenlexikon, “Hürlimann H 356” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | — | No figureNo call on PTO independence: not stated for the H-356 (A). |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 55-66 V/F/55-66 V/F/DT” | 2WD / 4WDTraktorenlexikon, “Hürlimann H 356” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1992 | 1983–1986 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Hürlimann H-356 (A) is 60% heavier (920 kg / 2,028 lb) than the Fiat 55-66 V/F (DT-V/F) (both unladen weight, as stated by the source).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources