Fahr D 25 N or International Harvester Super FC-C?
Which should you choose?
On performance, no comparable figure differs by more than its threshold: on this data the machines are level. On features, the Fahr D 25 N is ahead on top speed and PTO independence.
- The Fahr D 25 N suits PTO-driven implements (mowers, balers, pumps) better on this data: an independent PTO.
- The Fahr D 25 N suits road haulage better on this data: 12% (2.0 km/h / 1.2 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 25 N | Super FC-C | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 17.7 kW (24 hp)Traktorenlexikon, “Fahr D 25 N” | 18.0 kW (24.2 hp)Traktorenlexikon, “McCormick Super FC-C” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 25 N and the Super FC-C. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 25 N and the Super FC-C. |
| Which pumps more oil for implements? | — | 17.3 L/min (4.6 gpm)Traktorenlexikon, “McCormick Super FC-C” | No figureNo call on hydraulic flow: no figure on record for the D 25 N. |
| Which lifts more on the three-point hitch? | 690 kg (1,521 lb)Traktorenlexikon, “Fahr D 25 N” | 700 kg (1,543 lb)Traktorenlexikon, “McCormick Super FC-C” | EvenNo call on three-point lift: the sources do not state where the lift was measured, so the difference is not a reliable call. |
| Which is heavier, for traction? | 1,853 kg (4,085 lb)Traktorenlexikon, “Fahr D 25 N” | 1,440 kg (3,175 lb)Traktorenlexikon, “McCormick Super FC-C” | Ahead (a fact, not an advantage)The Fahr D 25 N is 29% heavier (413 kg / 911 lb) than the International Harvester Super FC-C (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 3,300 kg (7,275 lb)Traktorenlexikon, “Fahr D 25 N” | — | No figureNo call on maximum permissible mass: no figure on record for the Super FC-C. |
| Which has the wider choice of gears? | 5 to 6Traktorenlexikon, “Fahr D 25 N” | 4Traktorenlexikon, “McCormick Super FC-C” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 25 N and the Super FC-C. |
| Which is faster on the road? | 19 km/h (11.8 mph)Traktorenlexikon, “Fahr D 25 N” | 17 km/h (10.6 mph)Traktorenlexikon, “McCormick Super FC-C” | AheadThe Fahr D 25 N has 12% more top speed (2.0 km/h / 1.2 mph) than the International Harvester Super FC-C (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Fahr D 25 N” | 539 rpmTraktorenlexikon, “McCormick Super FC-C” | No figureNo call on PTO speeds: no standard PTO speed stated for the Super FC-C. |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Fahr D 25 N” | dependent (stops with the clutch)Traktorenlexikon, “McCormick Super FC-C” | AheadThe Fahr D 25 N has an independent PTO; the International Harvester Super FC-C’s is dependent (stops with the clutch). |
| Which drives on both axles? | 2WDTraktorenlexikon, “Fahr D 25 N” | 2WDTraktorenlexikon, “McCormick Super FC-C” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1953 | 1952–1957 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Fahr D 25 N is 29% heavier (413 kg / 911 lb) than the International Harvester Super FC-C (both unladen weight, as stated by the source).
- The Fahr D 25 N has 12% more top speed (2.0 km/h / 1.2 mph) than the International Harvester Super FC-C (both top speed forward, as stated by the source).
- The Fahr D 25 N has an independent PTO; the International Harvester Super FC-C’s is dependent (stops with the clutch).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- No call on three-point lift: the sources do not state where the lift was measured, so the difference is not a reliable call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on drive: all two-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, maximum permissible mass, a creeper range and PTO speeds.
← Every figure for both machines, side by side, with sources