Eicher Mammut 3012 A or Fahr D 540?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the Mammut 3012 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 540 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Eicher Mammut 3012 A suits loader and hydraulic implement work better on this data: 116% (21.5 L/min / 5.7 gpm) more hydraulic flow.
- The Eicher Mammut 3012 A suits heavy draft work (ploughing, cultivating) better on this data: four-wheel drive.
- The Fahr D 540 suits road haulage better on this data: 60% (12.0 km/h / 7.5 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Mammut 3012 A | D 540 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 45.4 kW (60.9 hp)Traktorenlexikon, “Eicher 3012 Mammut A” | 43.9 kW (58.9 hp)Traktorenlexikon, “Fahr D 540” | Not comparableNot comparable on power at the PTO shaft: the Mammut 3012 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 540 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Mammut 3012 A and the D 540. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Mammut 3012 A and the D 540. |
| Which pumps more oil for implements? | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Eicher 3012 Mammut A” | 18.5 L/min (4.9 gpm)Traktorenlexikon, “Fahr D 540” | AheadThe Eicher Mammut 3012 A has 116% more hydraulic flow (21.5 L/min / 5.7 gpm) than the Fahr D 540 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | — | No figureNo call on three-point lift: no figure on record for the Mammut 3012 A and the D 540. |
| Which is heavier, for traction? | 3,140 kg (6,923 lb)Traktorenlexikon, “Eicher 3012 Mammut A” | 3,330 kg (7,341 lb)Traktorenlexikon, “Fahr D 540” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | 4,100 kg (9,039 lb)Traktorenlexikon, “Fahr D 540” | No figureNo call on maximum permissible mass: no figure on record for the Mammut 3012 A. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Eicher 3012 Mammut A” | 5 to 7Traktorenlexikon, “Fahr D 540” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | YesTraktorenlexikon, “Eicher 3012 Mammut A” | — | No figureNo call on a creeper range: not stated for the D 540. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “Eicher 3012 Mammut A” | 32 km/h (19.9 mph)Traktorenlexikon, “Fahr D 540” | AheadThe Fahr D 540 has 60% more top speed (12.0 km/h / 7.5 mph) than the Eicher Mammut 3012 A (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Eicher 3012 Mammut A” | 540 rpmTraktorenlexikon, “Fahr D 540” | AheadThe Eicher Mammut 3012 A offers 1000 rpm at the PTO, which the Fahr D 540 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Eicher 3012 Mammut A” | dependent (stops with the clutch)Traktorenlexikon, “Fahr D 540” | AheadThe Eicher Mammut 3012 A has an independent PTO; the Fahr D 540’s is dependent (stops with the clutch). |
| Which drives on both axles? | 4WDTraktorenlexikon, “Eicher 3012 Mammut A” | 2WDTraktorenlexikon, “Fahr D 540” | AheadThe Eicher Mammut 3012 A is available with four-wheel drive; the Fahr D 540 is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1969–1970 | 1955–1958 | Ahead (a fact, not an advantage)The Eicher Mammut 3012 A is newer: production began 14 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Eicher Mammut 3012 A has 116% more hydraulic flow (21.5 L/min / 5.7 gpm) than the Fahr D 540 (both pump flow, as stated by the source).
- The Fahr D 540 has 60% more top speed (12.0 km/h / 7.5 mph) than the Eicher Mammut 3012 A (both top speed forward, as stated by the source).
- The Eicher Mammut 3012 A offers 1000 rpm at the PTO, which the Fahr D 540 does not (as stated by the sources).
- The Eicher Mammut 3012 A has an independent PTO; the Fahr D 540’s is dependent (stops with the clutch).
- The Eicher Mammut 3012 A is available with four-wheel drive; the Fahr D 540 is two-wheel drive (as stated by the sources).
- The Eicher Mammut 3012 A is newer: production began 14 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Not comparable on power at the PTO shaft: the Mammut 3012 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 540 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources