Dexheimer Allrad 345 N or Landini R-5500 (DT) "TL 22 N/A"?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the Allrad 345 N has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the R-5500 (DT) "TL 22 N/A" has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Dexheimer Allrad 345N suits loader and hydraulic implement work better on this data: 43% (12.4 L/min / 3.3 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Allrad 345 N | R-5500 (DT) "TL 22 N/A" | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 37 kW (50 hp)Traktorenlexikon, “Dexheimer ALLRAD 345 N” | 36.8 kW (49.3 hp)Traktorenlexikon, “Landini 5500” | Not comparableNot comparable on power at the PTO shaft: the Allrad 345 N has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the R-5500 (DT) "TL 22 N/A" has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Allrad 345 N and the R-5500 (DT) "TL 22 N/A". |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Allrad 345 N and the R-5500 (DT) "TL 22 N/A". |
| Which pumps more oil for implements? | 41 L/min (10.8 gpm)Traktorenlexikon, “Dexheimer ALLRAD 345 N” | 28.6 L/min (7.6 gpm)Traktorenlexikon, “Landini 5500” | AheadThe Dexheimer Allrad 345N has 43% more hydraulic flow (12.4 L/min / 3.3 gpm) than the Landini R-5500 (DT) "TL 22 N/A" (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,200 kg (4,850 lb)Traktorenlexikon, “Dexheimer ALLRAD 345 N” | 2,050 kg (4,519 lb)Traktorenlexikon, “Landini 5500” | Not comparableNot comparable on three-point lift: the Allrad 345 N: lift at an unstated point, as stated by the source (Traktorenlexikon, “Dexheimer ALLRAD 345 N”); the R-5500 (DT) "TL 22 N/A": lift at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 5500”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 1,625 kg (3,583 lb)Traktorenlexikon, “Dexheimer ALLRAD 345 N” | 2,010 kg (4,431 lb)Traktorenlexikon, “Landini 5500” | Ahead (a fact, not an advantage)The Landini R-5500 (DT) "TL 22 N/A" is 24% heavier (385 kg / 849 lb) than the Dexheimer Allrad 345N (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the Allrad 345 N and the R-5500 (DT) "TL 22 N/A". |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Dexheimer ALLRAD 345 N” | 12Traktorenlexikon, “Landini 5500” | AheadThe Landini R-5500 (DT) "TL 22 N/A" has 50% more forward gears (4 gears) than the Dexheimer Allrad 345N (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the Allrad 345 N and the R-5500 (DT) "TL 22 N/A". |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Dexheimer ALLRAD 345 N” | 25 km/h (15.5 mph)Traktorenlexikon, “Landini 5500” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | — | 540/1000 rpmTraktorenlexikon, “Landini 5500” | No figureNo call on PTO speeds: no standard PTO speed stated for the Allrad 345 N. |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the Allrad 345 N and the R-5500 (DT) "TL 22 N/A". |
| Which drives on both axles? | 4WDTraktorenlexikon, “Dexheimer ALLRAD 345 N” | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 5500” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1976–1985 | 1973–1983 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Dexheimer Allrad 345N has 43% more hydraulic flow (12.4 L/min / 3.3 gpm) than the Landini R-5500 (DT) "TL 22 N/A" (both pump flow, as stated by the source).
- The Landini R-5500 (DT) "TL 22 N/A" is 24% heavier (385 kg / 849 lb) than the Dexheimer Allrad 345N (both unladen weight, as stated by the source).
- The Landini R-5500 (DT) "TL 22 N/A" has 50% more forward gears (4 gears) than the Dexheimer Allrad 345N (both forward gears, as stated by the source).
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the Allrad 345 N has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the R-5500 (DT) "TL 22 N/A" has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the Allrad 345 N: lift at an unstated point, as stated by the source (Traktorenlexikon, “Dexheimer ALLRAD 345 N”); the R-5500 (DT) "TL 22 N/A": lift at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 5500”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources