Deutz-Fahr DX 86 or John Deere 5500 (A)?
Which should you choose?
The figures split: the John Deere 5500 (A) is ahead on hydraulic flow; the Deutz-Fahr DX 86 is ahead on three-point lift and PTO speeds.
- The Deutz-Fahr DX 86 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 86 | 5500 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 55.2 kW (74.0 hp)Traktorenlexikon, “Deutz-Fahr DX 86” | 55.2 kW (74.0 hp)Traktorenlexikon, “John Deere 5500 (USA)” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 86 and the 5500 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 86 and the 5500 (A). |
| Which pumps more oil for implements? | 39.6 L/min (10.5 gpm)Traktorenlexikon, “Deutz-Fahr DX 86” | 62.5 L/min (16.5 gpm)Traktorenlexikon, “John Deere 5500 (USA)” | AheadThe John Deere 5500 (A) has 58% more hydraulic flow (22.9 L/min / 6.0 gpm) than the Deutz-Fahr DX 86 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,800 kg (8,378 lb)Traktorenlexikon, “Deutz-Fahr DX 86” | 1,725 kg (3,803 lb)Traktorenlexikon, “John Deere 5500 (USA)” | AheadThe Deutz-Fahr DX 86 has 120% more lift (2,075 kg / 4,575 lb) than the John Deere 5500 (A) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,670 kg (8,091 lb)Traktorenlexikon, “Deutz-Fahr DX 86” | 2,573 kg (5,672 lb)Traktorenlexikon, “John Deere 5500 (USA)” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 86 is 43% heavier (1,097 kg / 2,418 lb) than the John Deere 5500 (A) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 86 and the 5500 (A). |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 86” | 9 to 12Traktorenlexikon, “John Deere 5500 (USA)” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 86 and the 5500 (A). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 86” | 30 km/h (18.6 mph)Traktorenlexikon, “John Deere 5500 (USA)” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 86” | 540 rpmTraktorenlexikon, “John Deere 5500 (USA)” | AheadThe Deutz-Fahr DX 86 offers 1000 rpm at the PTO, which the John Deere 5500 (A) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 86” | independentTraktorenlexikon, “John Deere 5500 (USA)” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr DX 86” | 2WD / 4WDTraktorenlexikon, “John Deere 5500 (USA)” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1982–1983 | 1995–1997 | Ahead (a fact, not an advantage)The John Deere 5500 (A) is newer: production began 13 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 5500 (A) has 58% more hydraulic flow (22.9 L/min / 6.0 gpm) than the Deutz-Fahr DX 86 (both pump flow, as stated by the source).
- The Deutz-Fahr DX 86 has 120% more lift (2,075 kg / 4,575 lb) than the John Deere 5500 (A) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 86 is 43% heavier (1,097 kg / 2,418 lb) than the John Deere 5500 (A) (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 86 offers 1000 rpm at the PTO, which the John Deere 5500 (A) does not (as stated by the sources).
- The John Deere 5500 (A) is newer: production began 13 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources