Deutz-Fahr DX 4.10 or Steyr 8080 (a)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the DX 4.10 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8080 (a) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz-Fahr DX 4.10 suits loader and hydraulic implement work better on this data: 46% (1,200 kg / 2,646 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 4.10 | 8080 (a) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 51.5 kW (69.1 hp)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 51.5 kW (69.1 hp)Traktorenlexikon, “Steyr 8080” | Not comparableNot comparable on power at the PTO shaft: the DX 4.10 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8080 (a) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 4.10 and the 8080 (a). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 4.10 and the 8080 (a). |
| Which pumps more oil for implements? | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Deutz-Fahr DX 4.10” | — | No figureNo call on hydraulic flow: no figure on record for the 8080 (a). |
| Which lifts more on the three-point hitch? | 3,800 kg (8,378 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 2,600 kg (5,732 lb)Traktorenlexikon, “Steyr 8080” | AheadThe Deutz-Fahr DX 4.10 has 46% more lift (1,200 kg / 2,646 lb) than the Steyr 8080 (a) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,920 kg (8,642 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 2,808 kg (6,191 lb)Traktorenlexikon, “Steyr 8080” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is 40% heavier (1,112 kg / 2,452 lb) than the Steyr 8080 (a) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 4.10 and the 8080 (a). |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 4.10” | 16 to 32Traktorenlexikon, “Steyr 8080” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 4.10 and the 8080 (a). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 25 km/h (15.5 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Steyr 8080” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 4.10” | 540/1000 rpmTraktorenlexikon, “Steyr 8080” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 4.10” | independentTraktorenlexikon, “Steyr 8080” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 4.10” | Two-wheel or four-wheel driveTraktorenlexikon, “Steyr 8080” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1988 | 1979–1992 | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 4.10 has 46% more lift (1,200 kg / 2,646 lb) than the Steyr 8080 (a) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 4.10 is 40% heavier (1,112 kg / 2,452 lb) than the Steyr 8080 (a) (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 4.10 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the DX 4.10 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8080 (a) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources