9 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 1451980–1983No measured PTO figureTractor twoLandini 14.500 (DT) "TL 24 N/G"1978–1993No measured PTO figure
Which should you choose?
Read our verdict on the DX 145 and the 14.500 (DT) "TL 24 N/G" → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | DX 145 | 14.500 (DT) "TL 24 N/G" | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 130 hp | 130.2 hp | — |
| Engine declared | KHD BF6L 913 | Perkins AT 6.354.4 | differs |
| Displacement declared | 6.13 L | 5.80 L | +6% DX 145 |
| Maximum torque declared | 371 lb·ft · 503 N·m | 359 lb·ft · 487 N·m | — |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | pedal operated dry single clutch | Pedal-operated dry LUK double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 14.7 gpm · 55.7 L/min | 16.4 gpm · 62.0 L/min | +11% 14.500 (DT) "TL 24 N/G" |
| Pressure declared | 3,191 psi · 220 bar | — | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 11,266 lb · 5,110 kg | 11,530 lb · 5,230 kg | — |
| Maximum permissible mass declared | 16,976 lb · 7,700 kg | — | — |
| Wheelbase declared | 105.9 in · 2,690 mm | 111.8 in · 2,840 mm | +6% 14.500 (DT) "TL 24 N/G" |
| Length declared | 177.2 in · 4,500 mm | 183.5 in · 4,660 mm | — |
| Width declared | 93.3 in · 2,370 mm | 91.7 in · 2,330 mm | — |
| Ground clearance declared | 22.8 in · 580 mm | 20.1 in · 510 mm | +14% DX 145 |
| Fuel tank declared | 132.1 qt · 125 L | 190.2 qt · 180.0 L | +44% 14.500 (DT) "TL 24 N/G" |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 145 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 145”
- Source: Traktorenlexikon, “Deutz-Fahr DX 160”
Landini 14.500 (DT) "TL 24 N/G" sources
- Source: Traktorenlexikon, “Landini 14500”
- Source: Traktorenlexikon, “Massey Ferguson MF 1134”