10 material differences · fewer than 12
Tractor oneDeutz-Fahr D 7207 (C)1980–1984No measured PTO figureTractor twoInternational Harvester 6851981–1990No measured PTO figure
Which should you choose?
Read our verdict on the D 7207 (C) and the 685 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | D 7207 (C) | 685 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 68 hp | 68.0 hp | — |
| Engine declared | KHD F4L 912 | INTERNATIONAL-HARVESTER D-239 | differs |
| Displacement declared | 3.77 L | 3.91 L | — |
| Maximum torque declared | 181 lb·ft · 245 N·m | 181 lb·ft · 245 N·m | — |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 15.5 mph · 25 km/h | differs |
| Clutch declared | Independent dry Fichtel & Sachs double clutch | Pedal operated dry LAYCOCK single disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 10.5 gpm · 39.6 L/min | — | — |
| Pressure declared | — | 2,698 psi · 186 bar | — |
| Three-point lift, at the coupling points declared | 5,732 lb · 2,600 kg | 4,398 lb · 1,995 kg | +30% D 7207 (C) |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,437 lb · 2,920 kg | 6,702 lb · 3,040 kg | — |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | — | — |
| Wheelbase declared | 95.0 in · 2,414 mm | 88.2 in · 2,240 mm | +8% D 7207 (C) |
| Length declared | 158.3 in · 4,020 mm | 147.2 in · 3,740 mm | +7% D 7207 (C) |
| Width declared | 78.3 in · 1,990 mm | 75.6 in · 1,920 mm | — |
| Ground clearance declared | 22.8 in · 580 mm | 14.6 in · 370 mm | +57% D 7207 (C) |
| Turning radius, braked declared | 12.5 ft · 3.81 m | 10.9 ft · 3.33 m | +14% D 7207 (C) |
| Fuel tank declared | 95.1–97.2 qt · 90–92 L | 118.3 qt · 112.0 L | differs |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr D 7207 (C) sources
- Source: Traktorenlexikon, “Deutz-Fahr D 7207”
- Source: Traktorenlexikon, “Deutz D 6006”
International Harvester 685 sources
- Source: Traktorenlexikon, “IHC 685 (XL)”
- Source: Traktorenlexikon, “IHC 574”