9 material differences · fewer than 12
Tractor oneDeutz-Fahr D 7207 (C)1980–1984No measured PTO figureTractor twoDeutz (KHD) Intrac 20041978–1989No measured PTO figure
Which should you choose?
Read our verdict on the D 7207 (C) and the Intrac 2004 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | D 7207 (C) | Intrac 2004 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 68 hp | 68.7 hp | — |
| Engine declared | KHD F4L 912 | KHD F4L 912 H | differs |
| Displacement declared | 3.77 L | 3.77 L | — |
| Maximum torque declared | 181 lb·ft · 245 N·m | 175 lb·ft · 237 N·m | — |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Independent dry Fichtel & Sachs double clutch | — | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Pump flow declared | 10.5 gpm · 39.6 L/min | 12.4 gpm · 47.1 L/min | +19% Intrac 2004 |
| Pressure declared | — | 2,538 psi · 175 bar | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,437 lb · 2,920 kg | 7,055 lb · 3,200 kg | +10% Intrac 2004 |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | 11,795 lb · 5,350 kg | +7% Intrac 2004 |
| Wheelbase declared | 95.0 in · 2,414 mm | 86.6 in · 2,200 mm | +10% D 7207 (C) |
| Length declared | 158.3 in · 4,020 mm | 140.2 in · 3,560 mm | +13% D 7207 (C) |
| Width declared | 78.3 in · 1,990 mm | 79.7 in · 2,025 mm | — |
| Ground clearance declared | 22.8 in · 580 mm | 14.0 in · 355 mm | +63% D 7207 (C) |
| Turning radius, braked declared | 12.5 ft · 3.81 m | — | — |
| Fuel tank declared | 95.1–97.2 qt · 90–92 L | — | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr D 7207 (C) sources
- Source: Traktorenlexikon, “Deutz-Fahr D 7207”
- Source: Traktorenlexikon, “Deutz D 6006”
Deutz (KHD) Intrac 2004 sources
- Source: Traktorenlexikon, “Deutz INTRAC 2004”