5 material differences · fewer than 12
Tractor oneDeutz-Fahr D 7007 (C)1982–1984No measured PTO figureTractor twoDeutz-Fahr D 7207 (C)1980–1984No measured PTO figure
Which should you choose?
Read our verdict on the D 7007 (C) and the D 7207 (C) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
5 material differences · 11 fields identical or within 5%, which is not counted as material
| Field | D 7007 (C) | D 7207 (C) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 68 hp | 68 hp | — |
| Engine declared | KHD F4L 912 | KHD F4L 912 | — |
| Displacement declared | 3.77 L | 3.77 L | — |
| Maximum torque declared | 181 lb·ft · 245 N·m | 181 lb·ft · 245 N·m | — |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 15.5–18.6 mph · 25–30 km/h | — |
| Clutch declared | Independent dry double clutch | Independent dry Fichtel & Sachs double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | — | 10.5 gpm · 39.6 L/min | — |
| Three-point lift, at the coupling points declared | 5,732 lb · 2,600 kg | 5,732 lb · 2,600 kg | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540 rpm / 1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 6,305 lb · 2,860 kg | 6,437 lb · 2,920 kg | — |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | 11,023 lb · 5,000 kg | — |
| Wheelbase declared | 85.4 in · 2,170 mm | 95.0 in · 2,414 mm | +11% D 7207 (C) |
| Length declared | 148.0 in · 3,760 mm | 158.3 in · 4,020 mm | +7% D 7207 (C) |
| Width declared | 78.3 in · 1,990 mm | 78.3 in · 1,990 mm | — |
| Ground clearance declared | 21.7 in · 550 mm | 22.8 in · 580 mm | +5% D 7207 (C) |
| Turning radius, braked declared | 11.5 ft · 3.50 m | 12.5 ft · 3.81 m | +9% D 7207 (C) |
| Fuel tank declared | 97.2 qt · 92 L | 95.1–97.2 qt · 90–92 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr D 7007 (C) sources
- Source: Traktorenlexikon, “Deutz-Fahr D 7007”
- Source: Traktorenlexikon, “Deutz D 6006”
Deutz-Fahr D 7207 (C) sources
- Source: Traktorenlexikon, “Deutz-Fahr D 7207”
- Source: Traktorenlexikon, “Deutz D 6006”