Deutz-Fahr Agrotron K 100 (Profiline) or Fiat TL 100 (DT)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the Agrotron K 100 (Profiline) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the TL 100 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz-Fahr Agrotron K 100 (Profiline) suits loader and hydraulic implement work better on this data: 60% (2,340 kg / 5,159 lb) more three-point lift.
- The Deutz-Fahr Agrotron K 100 (Profiline) suits road haulage better on this data: 25% (1,500 kg / 3,307 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Agrotron K 100 (Profiline) | TL 100 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 69.9 kW (93.7 hp)Traktorenlexikon, “Deutz-Fahr Agrotron K 100” | 69.9 kW (93.7 hp)Traktorenlexikon, “Fiatagri TL100” | Not comparableNot comparable on power at the PTO shaft: the Agrotron K 100 (Profiline) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the TL 100 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Agrotron K 100 (Profiline) and the TL 100 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Agrotron K 100 (Profiline) and the TL 100 (DT). |
| Which pumps more oil for implements? | — | 60.0 L/min (15.9 gpm)Traktorenlexikon, “Fiatagri TL100” | No figureNo call on hydraulic flow: no figure on record for the Agrotron K 100 (Profiline). |
| Which lifts more on the three-point hitch? | 6,220 kg (13,713 lb)Traktorenlexikon, “Deutz-Fahr Agrotron K 100” | 3,880 kg (8,554 lb)Traktorenlexikon, “Fiatagri TL100” | AheadThe Deutz-Fahr Agrotron K 100 (Profiline) has 60% more lift (2,340 kg / 5,159 lb) than the Fiat TL 100 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 4,440 kg (9,789 lb)Traktorenlexikon, “Deutz-Fahr Agrotron K 100” | 4,365 kg (9,623 lb)Traktorenlexikon, “Fiatagri TL100” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 7,500 kg (16,535 lb)Traktorenlexikon, “Deutz-Fahr Agrotron K 100” | 6,000 kg (13,228 lb)Traktorenlexikon, “Fiatagri TL100” | AheadThe Deutz-Fahr Agrotron K 100 (Profiline) has 25% higher maximum permissible mass (1,500 kg / 3,307 lb) than the Fiat TL 100 (DT) (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 24Traktorenlexikon, “Deutz-Fahr Agrotron K 100” | 20 to 24Traktorenlexikon, “Fiatagri TL100” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | YesTraktorenlexikon, “Fiatagri TL100” | No figureNo call on a creeper range: not stated for the Agrotron K 100 (Profiline). |
| Which is faster on the road? | 40 km/h (24.9 mph) to 50 km/h (31.1 mph)Traktorenlexikon, “Deutz-Fahr Agrotron K 100” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Fiatagri TL100” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540 rpm / 1000 rpmTraktorenlexikon, “Deutz-Fahr Agrotron K 100” | 540/540E/1000 rpmTraktorenlexikon, “Fiatagri TL100” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the Agrotron K 100 (Profiline) and the TL 100 (DT). |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr Agrotron K 100” | Two-wheel or four-wheel driveTraktorenlexikon, “Fiatagri TL100” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 2005–2008 | 1998–2004 | Ahead (a fact, not an advantage)The Deutz-Fahr Agrotron K 100 (Profiline) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr Agrotron K 100 (Profiline) has 60% more lift (2,340 kg / 5,159 lb) than the Fiat TL 100 (DT) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr Agrotron K 100 (Profiline) has 25% higher maximum permissible mass (1,500 kg / 3,307 lb) than the Fiat TL 100 (DT) (both maximum permissible mass, as stated by the source).
- The Deutz-Fahr Agrotron K 100 (Profiline) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the Agrotron K 100 (Profiline) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the TL 100 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources