Deutz-Fahr Agrotron 6.45 or VALMET 2005-4?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr Agrotron 6.45: hydraulic flow and three-point lift. It is also ahead on forward gears.
- The Deutz-Fahr Agrotron 6.45 suits loader and hydraulic implement work better on this data: 33% (20.4 L/min / 5.4 gpm) more hydraulic flow and 57% (2,668 kg / 5,882 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Agrotron 6.45 | 2005-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 95.3 kW (127.8 hp)Traktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 95.8 kW (128.5 hp)Traktorenlexikon, “Valmet 2005” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Agrotron 6.45 and the 2005-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Agrotron 6.45 and the 2005-4. |
| Which pumps more oil for implements? | 83.0 L/min (21.9 gpm)Traktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 62.6 L/min (16.5 gpm)Traktorenlexikon, “Valmet 2005” | AheadThe Deutz-Fahr Agrotron 6.45 has 33% more hydraulic flow (20.4 L/min / 5.4 gpm) than the VALMET 2005-4 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 7,388 kg (16,287 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 4,720 kg (10,406 lb)Traktorenlexikon, “Valmet 2005” | AheadThe Deutz-Fahr Agrotron 6.45 has 57% more lift (2,668 kg / 5,882 lb) than the VALMET 2005-4 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 5,390 kg (11,883 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 6,335 kg (13,966 lb)Traktorenlexikon, “Valmet 2005” | Ahead (a fact, not an advantage)The VALMET 2005-4 is 18% heavier (945 kg / 2,083 lb) than the Deutz-Fahr Agrotron 6.45 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the Agrotron 6.45 and the 2005-4. |
| Which has the wider choice of gears? | 24Traktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 16Traktorenlexikon, “Valmet 2005” | AheadThe Deutz-Fahr Agrotron 6.45 has 50% more forward gears (8 gears) than the VALMET 2005-4 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the Agrotron 6.45 and the 2005-4. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 50 km/h (31.1 mph)Traktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 2005” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 540/1000 rpmTraktorenlexikon, “Valmet 2005” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr Agrotron 6.45” | — | No figureNo call on PTO independence: not stated for the 2005-4. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr Agrotron 6.45” | 4WDTraktorenlexikon, “Valmet 2005” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1995–1997 | 1986–1987 | Ahead (a fact, not an advantage)The Deutz-Fahr Agrotron 6.45 is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr Agrotron 6.45 has 33% more hydraulic flow (20.4 L/min / 5.4 gpm) than the VALMET 2005-4 (both pump flow, as stated by the source).
- The Deutz-Fahr Agrotron 6.45 has 57% more lift (2,668 kg / 5,882 lb) than the VALMET 2005-4 (both lift at the hitch ends, as stated by the source).
- The VALMET 2005-4 is 18% heavier (945 kg / 2,083 lb) than the Deutz-Fahr Agrotron 6.45 (both unladen weight, as stated by the source).
- The Deutz-Fahr Agrotron 6.45 has 50% more forward gears (8 gears) than the VALMET 2005-4 (both forward gears, as stated by the source).
- The Deutz-Fahr Agrotron 6.45 is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources