Deutz-Fahr Agrotron 160 or Steyr 8180 a?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the Agrotron 160 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8180 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz-Fahr Agrotron 160 suits loader and hydraulic implement work better on this data: 119% (62.6 L/min / 16.5 gpm) more hydraulic flow and 51% (3,380 kg / 7,452 lb) more three-point lift.
- The Deutz-Fahr Agrotron 160 suits road haulage better on this data: 41% (3,500 kg / 7,716 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Agrotron 160 | 8180 a | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 117.8 kW (158.0 hp)Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 117.8 kW (158.0 hp)Traktorenlexikon, “Steyr 8180” | Not comparableNot comparable on power at the PTO shaft: the Agrotron 160 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8180 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Agrotron 160 and the 8180 a. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Agrotron 160 and the 8180 a. |
| Which pumps more oil for implements? | 115.0 L/min (30.4 gpm)Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 52.4 L/min (13.8 gpm)Traktorenlexikon, “Steyr 8180” | AheadThe Deutz-Fahr Agrotron 160 has 119% more hydraulic flow (62.6 L/min / 16.5 gpm) than the Steyr 8180a (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 10,000 kg (22,046 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 6,620 kg (14,595 lb)Traktorenlexikon, “Steyr 8180” | AheadThe Deutz-Fahr Agrotron 160 has 51% more lift (3,380 kg / 7,452 lb) than the Steyr 8180a (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 6,900 kg (15,212 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 6,012 kg (13,254 lb)Traktorenlexikon, “Steyr 8180” | Ahead (a fact, not an advantage)The Deutz-Fahr Agrotron 160 is 15% heavier (888 kg / 1,958 lb) than the Steyr 8180a (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 12,000 kg (26,455 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 8,500 kg (18,739 lb)Traktorenlexikon, “Steyr 8180” | AheadThe Deutz-Fahr Agrotron 160 has 41% higher maximum permissible mass (3,500 kg / 7,716 lb) than the Steyr 8180a (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 18Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 12 to 36Traktorenlexikon, “Steyr 8180” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the Agrotron 160 and the 8180 a. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr Agrotron 160” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Steyr 8180” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540E/1000 rpmTraktorenlexikon, “Deutz-Fahr Agrotron 160” | 1000 rpmTraktorenlexikon, “Steyr 8180” | AheadThe Deutz-Fahr Agrotron 160 offers 540 rpm at the PTO, which the Steyr 8180a does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Steyr 8180” | No figureNo call on PTO independence: not stated for the Agrotron 160. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr Agrotron 160” | 4WDTraktorenlexikon, “Steyr 8180” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1997–2001 | 1986–1993 | Ahead (a fact, not an advantage)The Deutz-Fahr Agrotron 160 is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr Agrotron 160 has 119% more hydraulic flow (62.6 L/min / 16.5 gpm) than the Steyr 8180a (both pump flow, as stated by the source).
- The Deutz-Fahr Agrotron 160 has 51% more lift (3,380 kg / 7,452 lb) than the Steyr 8180a (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr Agrotron 160 is 15% heavier (888 kg / 1,958 lb) than the Steyr 8180a (both unladen weight, as stated by the source).
- The Deutz-Fahr Agrotron 160 has 41% higher maximum permissible mass (3,500 kg / 7,716 lb) than the Steyr 8180a (both maximum permissible mass, as stated by the source).
- The Deutz-Fahr Agrotron 160 offers 540 rpm at the PTO, which the Steyr 8180a does not (as stated by the sources).
- The Deutz-Fahr Agrotron 160 is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the Agrotron 160 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8180 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources