Deutz-Fahr AgroStar 6.08 or Landini 11800 (DT)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the AgroStar 6.08 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 11800 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz-Fahr AgroStar 6.08 suits loader and hydraulic implement work better on this data: 12% (6.3 L/min / 1.7 gpm) more hydraulic flow and 16% (703 kg / 1,550 lb) more three-point lift.
- The Deutz-Fahr AgroStar 6.08 suits road haulage better on this data: 21% (1,500 kg / 3,307 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | AgroStar 6.08 | 11800 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 78.8 kW (105.7 hp)Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 78.8 kW (105.7 hp)Traktorenlexikon, “Landini 11800 DT” | Not comparableNot comparable on power at the PTO shaft: the AgroStar 6.08 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 11800 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the AgroStar 6.08 and the 11800 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the AgroStar 6.08 and the 11800 (DT). |
| Which pumps more oil for implements? | 57.5 L/min (15.2 gpm)Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 51.2 L/min (13.5 gpm)Traktorenlexikon, “Landini 11800 DT” | AheadThe Deutz-Fahr AgroStar 6.08 has 12% more hydraulic flow (6.3 L/min / 1.7 gpm) than the Landini 11800 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 5,200 kg (11,464 lb)Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 4,497 kg (9,914 lb)Traktorenlexikon, “Landini 11800 DT” | AheadThe Deutz-Fahr AgroStar 6.08 has 16% more lift (703 kg / 1,550 lb) than the Landini 11800 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 4,540 kg (10,009 lb)Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 4,390 kg (9,678 lb)Traktorenlexikon, “Landini 11800 DT” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 8,500 kg (18,739 lb)Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 7,000 kg (15,432 lb)Traktorenlexikon, “Landini 11800 DT” | AheadThe Deutz-Fahr AgroStar 6.08 has 21% higher maximum permissible mass (1,500 kg / 3,307 lb) than the Landini 11800 (DT) (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 40 to 48Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 32Traktorenlexikon, “Landini 11800 DT” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | YesTraktorenlexikon, “Deutz-Fahr AgroStar 6.08” | — | No figureNo call on a creeper range: not stated for the 11800 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Landini 11800 DT” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000/750 rpmTraktorenlexikon, “Deutz-Fahr AgroStar 6.08” | 540/1000 rpmTraktorenlexikon, “Landini 11800 DT” | AheadThe Deutz-Fahr AgroStar 6.08 offers 750 rpm at the PTO, which the Landini 11800 (DT) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr AgroStar 6.08” | — | No figureNo call on PTO independence: not stated for the 11800 (DT). |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr AgroStar 6.08” | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 11800 DT” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1993–1995 | 1987–2000 | Ahead (a fact, not an advantage)The Deutz-Fahr AgroStar 6.08 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr AgroStar 6.08 has 12% more hydraulic flow (6.3 L/min / 1.7 gpm) than the Landini 11800 (DT) (both pump flow, as stated by the source).
- The Deutz-Fahr AgroStar 6.08 has 16% more lift (703 kg / 1,550 lb) than the Landini 11800 (DT) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr AgroStar 6.08 has 21% higher maximum permissible mass (1,500 kg / 3,307 lb) than the Landini 11800 (DT) (both maximum permissible mass, as stated by the source).
- The Deutz-Fahr AgroStar 6.08 offers 750 rpm at the PTO, which the Landini 11800 (DT) does not (as stated by the sources).
- The Deutz-Fahr AgroStar 6.08 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the AgroStar 6.08 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 11800 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources