Deutz-Fahr AgroStar 4.78 or Renault 110-54 TX?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the AgroStar 4.78 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 110-54 TX has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Renault 110-54 TX suits loader and hydraulic implement work better on this data: 40% (2,060 kg / 4,542 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | AgroStar 4.78 | 110-54 TX | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 73.6 kW (98.7 hp)Traktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 73.6 kW (98.7 hp)Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | Not comparableNot comparable on power at the PTO shaft: the AgroStar 4.78 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 110-54 TX has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the AgroStar 4.78 and the 110-54 TX. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the AgroStar 4.78 and the 110-54 TX. |
| Which pumps more oil for implements? | — | 41.1 L/min (10.9 gpm)Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | No figureNo call on hydraulic flow: no figure on record for the AgroStar 4.78. |
| Which lifts more on the three-point hitch? | 5,200 kg (11,464 lb)Traktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 7,260 kg (16,006 lb)Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | AheadThe Renault 110-54 TX has 40% more lift (2,060 kg / 4,542 lb) than the Deutz-Fahr AgroStar 4.78 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 4,200 kg (9,259 lb)Traktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 5,040 kg (11,111 lb)Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | Ahead (a fact, not an advantage)The Renault 110-54 TX is 20% heavier (840 kg / 1,852 lb) than the Deutz-Fahr AgroStar 4.78 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 7,500 kg (16,535 lb)Traktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 8,100 kg (17,857 lb)Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | EvenEven on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which has the wider choice of gears? | 40 to 48Traktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 16Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | AheadThe Deutz-Fahr AgroStar 4.78 has 150% more forward gears (24 gears) than the Renault 110-54 TX (both forward gears, as stated by the source). |
| Which offers a creeper range? | YesTraktorenlexikon, “Deutz-Fahr AgroStar 4.78” | — | No figureNo call on a creeper range: not stated for the 110-54 TX. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000/750 rpmTraktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 540/1000 rpmTraktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | AheadThe Deutz-Fahr AgroStar 4.78 offers 750 rpm at the PTO, which the Renault 110-54 TX does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr AgroStar 4.78” | independentTraktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr AgroStar 4.78” | 4WDTraktorenlexikon, “Renault 110-54 TE/TA/TS/TX/TZ R7912” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1993–1995 | 1989–1990 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Renault 110-54 TX has 40% more lift (2,060 kg / 4,542 lb) than the Deutz-Fahr AgroStar 4.78 (both lift at the hitch ends, as stated by the source).
- The Renault 110-54 TX is 20% heavier (840 kg / 1,852 lb) than the Deutz-Fahr AgroStar 4.78 (both unladen weight, as stated by the source).
- The Deutz-Fahr AgroStar 4.78 has 150% more forward gears (24 gears) than the Renault 110-54 TX (both forward gears, as stated by the source).
- The Deutz-Fahr AgroStar 4.78 offers 750 rpm at the PTO, which the Renault 110-54 TX does not (as stated by the sources).
- Even on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the AgroStar 4.78 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 110-54 TX has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow and a creeper range.
← Every figure for both machines, side by side, with sources