Deutz-Fahr Agrocompact 3.30 V/F or Renault 58-12 MX?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the Agrocompact 3.30 V/F has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 58-12 MX has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Renault 58-12 MX suits loader and hydraulic implement work better on this data: 30% (670 kg / 1,477 lb) more three-point lift.
- The Deutz-Fahr Agrocompact 3.30 V/F suits heavy draft work (ploughing, cultivating) better on this data: four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Agrocompact 3.30 V/F | 58-12 MX | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 39.7 kW (53.2 hp)Traktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 39.7 kW (53.2 hp)Traktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | Not comparableNot comparable on power at the PTO shaft: the Agrocompact 3.30 V/F has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 58-12 MX has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Agrocompact 3.30 V/F and the 58-12 MX. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Agrocompact 3.30 V/F and the 58-12 MX. |
| Which pumps more oil for implements? | — | — | No figureNo call on hydraulic flow: no figure on record for the Agrocompact 3.30 V/F and the 58-12 MX. |
| Which lifts more on the three-point hitch? | 2,200.000 kg (4,850 lb)Traktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 2,870 kg (6,327 lb)Traktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | AheadThe Renault 58-12 MX has 30% more lift (670 kg / 1,477 lb) than the Deutz-Fahr Agrocompact 3.30 V/F (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,150 kg (4,740 lb) to 2,350 kg (5,181 lb)Traktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 2,555 kg (5,633 lb)Traktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 4,375 kg (9,645 lb)Traktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | EvenEven on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which has the wider choice of gears? | 16Traktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 12 to 24Traktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the Agrocompact 3.30 V/F and the 58-12 MX. |
| Which is faster on the road? | 35 km/h (21.7 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540 rpm / 1000 rpmTraktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 540/1000 rpmTraktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | — | No figureNo call on PTO independence: not stated for the 58-12 MX. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr AgroCompact 3.30” | 2WDTraktorenlexikon, “Renault 58-32 ME/MA/MS/MX R3111” | AheadThe Deutz-Fahr Agrocompact 3.30 V/F is available with four-wheel drive; the Renault 58-12 MX is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1992–1996 | 1989–1993 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Renault 58-12 MX has 30% more lift (670 kg / 1,477 lb) than the Deutz-Fahr Agrocompact 3.30 V/F (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr Agrocompact 3.30 V/F is available with four-wheel drive; the Renault 58-12 MX is two-wheel drive (as stated by the sources).
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the Agrocompact 3.30 V/F has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 58-12 MX has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources