10 material differences · fewer than 12
Tractor oneDeutz (KHD) D 60061968–1974No measured PTO figureTractor twoFiat 650-S (DT)1971–1974No measured PTO figure
Which should you choose?
Read our verdict on the D 6006 and the 650-S (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | D 6006 | 650-S (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 62 hp | 69.1 hp | +12% 650-S (DT) |
| Engine declared | KHD F4L 912 | O.M.-FIAT CN 3 | differs |
| Displacement declared | 3.77 L | 3.71 L | — |
| Maximum torque declared | 161 lb·ft · 218 N·m | 203 lb·ft · 275 N·m | +26% 650-S (DT) |
| Transmission | |||
| Top speed declared | 17.1 mph · 27.6 km/h | 14.9 mph · 24 km/h | +15% D 6006 |
| Clutch declared | — | Dry FEREDO double clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | — | 7.6 gpm · 28.8 L/min | — |
| Pressure declared | 3,556 psi · 245 bar | 2,843 psi · 196 bar | +25% D 6006 |
| Rear PTO speeds declared | 540 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,699 lb · 2,585 kg | 6,338 lb · 2,875 kg | +11% 650-S (DT) |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | — | — |
| Wheelbase declared | 84.6 in · 2,150 mm | 91.3 in · 2,320 mm | +8% 650-S (DT) |
| Length declared | 146.5 in · 3,720 mm | 148.4 in · 3,770 mm | — |
| Width declared | 77.0 in · 1,955 mm | 69.3 in · 1,760 mm | +11% D 6006 |
| Ground clearance declared | 19.9 in · 505 mm | 20.1 in · 510 mm | — |
| Turning radius, braked declared | 11.0 ft · 3.34 m | 12.0 ft · 3.65 m | +9% 650-S (DT) |
| Fuel tank declared | 97.2 qt · 92 L | 82.4 qt · 78.0 L | +18% D 6006 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz (KHD) D 6006 sources
- Source: Traktorenlexikon, “Deutz D 6006”
Fiat 650-S (DT) sources
- Source: Traktorenlexikon, “Fiat 650 S/650 S/DT”
- Source: Traktorenlexikon, “Someca 650”