Deutz (KHD) D 25.2 or Hanomag C 220?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the D 25.2 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the C 220 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz D 25.2 suits loader and hydraulic implement work better on this data: 14% (2.0 L/min / 0.5 gpm) more hydraulic flow.
- The Deutz D 25.2 suits road haulage better on this data: 15% (300 kg / 661 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 25.2 | C 220 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 14.6 kW (19.6 hp)Traktorenlexikon, “Deutz D 25.2” | 14.6 kW (19.6 hp)Traktorenlexikon, “Hanomag C 220” | Not comparableNot comparable on power at the PTO shaft: the D 25.2 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the C 220 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 25.2 and the C 220. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 25.2 and the C 220. |
| Which pumps more oil for implements? | 16.0 L/min (4.2 gpm)Traktorenlexikon, “Deutz D 25.2” | 14.0 L/min (3.7 gpm)Traktorenlexikon, “Hanomag C 220” | AheadThe Deutz D 25.2 has 14% more hydraulic flow (2.0 L/min / 0.5 gpm) than the Hanomag C 220 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,250 kg (2,756 lb)Traktorenlexikon, “Deutz D 25.2” | 1,020 kg (2,249 lb)Traktorenlexikon, “Hanomag C 220” | EvenNo call on three-point lift: the sources do not state where the lift was measured, so the difference is not a reliable call. |
| Which is heavier, for traction? | 1,290 kg (2,844 lb)Traktorenlexikon, “Deutz D 25.2” | 1,370 kg (3,020 lb)Traktorenlexikon, “Hanomag C 220” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 2,300 kg (5,071 lb)Traktorenlexikon, “Deutz D 25.2” | 1,650 kg (3,638 lb) to 2,000 kg (4,409 lb)Traktorenlexikon, “Hanomag C 220” | AheadThe Deutz D 25.2 has 15% higher maximum permissible mass (300 kg / 661 lb) than the Hanomag C 220 (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Deutz D 25.2” | 6Traktorenlexikon, “Hanomag C 220” | AheadThe Deutz D 25.2 has 33% more forward gears (2 gears) than the Hanomag C 220 (both forward gears, as stated by the source). |
| Which offers a creeper range? | YesTraktorenlexikon, “Deutz D 25.2” | — | No figureNo call on a creeper range: not stated for the C 220. |
| Which is faster on the road? | 20.0 km/h (12.4 mph) to 26.4 km/h (16.4 mph)Traktorenlexikon, “Deutz D 25.2” | 19.8 km/h (12.3 mph)Traktorenlexikon, “Hanomag C 220” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Deutz D 25.2” | 1260Traktorenlexikon, “Hanomag C 220” | No figureNo call on PTO speeds: no standard PTO speed stated for the C 220. |
| Which PTO runs independently of the ground drive? | dependent (stops with the clutch)Traktorenlexikon, “Deutz D 25.2” | — | No figureNo call on PTO independence: not stated for the C 220. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Deutz D 25.2” | 2WDTraktorenlexikon, “Hanomag C 220” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1960–1964 | 1959–1960 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz D 25.2 has 14% more hydraulic flow (2.0 L/min / 0.5 gpm) than the Hanomag C 220 (both pump flow, as stated by the source).
- The Deutz D 25.2 has 15% higher maximum permissible mass (300 kg / 661 lb) than the Hanomag C 220 (both maximum permissible mass, as stated by the source).
- The Deutz D 25.2 has 33% more forward gears (2 gears) than the Hanomag C 220 (both forward gears, as stated by the source).
- No call on three-point lift: the sources do not state where the lift was measured, so the difference is not a reliable call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on drive: all two-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the D 25.2 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the C 220 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources