DEUTZ-ALLIS 9190 vs John Deere 8110
12 material differences
Which should you choose?
We will not advise between these two machines, because the drive differs (Two-wheel or four-wheel drive; 4WD); they were not built in overlapping years (1989–1990; 1999–2002). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
12 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 9190 | 8110 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 193.4 hp | 192.4 hp | — |
| Engine declared | K.H.D. BF6L 513 R-T | John Deere-PowerTech 6.081 HRW-11 | differs |
| Displacement declared | 9.57 L | 8.13 L | +18% 9190 |
| Maximum torque declared | — | 586 lb·ft · 794 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Pedal-operated dry Rockford double clutch | Pedal operated hydraulic wet John Deere multi-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Closed centre | Closed centre | — |
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | 28.0 gpm · 105.9 L/min | 31.8 gpm · 120.4 L/min | +14% 8110 |
| Pressure declared | 3,771 psi · 260 bar | 2,683 psi · 185 bar | +41% 9190 |
| Three-point lift at ends declared | 7,965 lb · 3,613 kg | — | — |
| Rear PTO speeds declared | 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 16,601 lb · 7,530 kg | 19,346 lb · 8,775 kg | +17% 8110 |
| Maximum permissible mass declared | — | 30,865 lb · 14,000 kg | — |
| Wheelbase declared | 115.0 in · 2,921 mm | 116.1 in · 2,950 mm | — |
| Length declared | 200.0 in · 5,080 mm | 216.0 in · 5,487 mm | +8% 8110 |
| Width declared | 96.0 in · 2,438 mm | 118.6 in · 3,012 mm | +24% 8110 |
| Height declared | 122.0 in · 3,099 mm | 121.7 in · 3,090 mm | — |
| Ground clearance declared | 22.0 in · 559 mm | 16.5 in · 420 mm | +33% 9190 |
| Turning radius, braked declared | 16.6 ft · 5.05 m | — | — |
| Fuel tank declared | 367.7 qt · 348.0 L | 540.0 qt · 511.0 L | +47% 8110 |
DEUTZ-ALLIS 9190 sources
Source
- Source: Traktorenlexikon, “Deutz-Allis 9190”
- Source: Traktorenlexikon, “Deutz-Allis 9170”
John Deere 8110 sources
Source
- Source: Traktorenlexikon, “John Deere 8110”
- Source: OECD test report 1931, 2000