DEUTZ-ALLIS 9190 or J.I. Case 4494?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 9190 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4494 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The DEUTZ-ALLIS 9190 suits loader and hydraulic implement work better on this data: 80% (47.2 L/min / 12.5 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 9190 | 4494 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 144.2 kW (193.4 hp)Traktorenlexikon, “Deutz-Allis 9190” | 142.7 kW (191.4 hp)Traktorenlexikon, “Case 4494” | Not comparableNot comparable on power at the PTO shaft: the 9190 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4494 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 9190 and the 4494. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 9190 and the 4494. |
| Which pumps more oil for implements? | 105.9 L/min (28.0 gpm)Traktorenlexikon, “Deutz-Allis 9190” | 58.7 L/min (15.5 gpm)Traktorenlexikon, “Case 4494” | AheadThe DEUTZ-ALLIS 9190 has 80% more hydraulic flow (47.2 L/min / 12.5 gpm) than the J.I. Case 4494 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,613 kg (7,965 lb)Traktorenlexikon, “Deutz-Allis 9190” | 5,780 kg (12,743 lb)Traktorenlexikon, “Case 4494” | Not comparableNot comparable on three-point lift: the 9190: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Allis 9190”); the 4494: lift through the full range 610 mm behind the ends, as stated by the source (Traktorenlexikon, “Case 4494”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 7,530 kg (16,601 lb)Traktorenlexikon, “Deutz-Allis 9190” | 9,453 kg (20,840 lb)Traktorenlexikon, “Case 4494” | Ahead (a fact, not an advantage)The J.I. Case 4494 is 26% heavier (1,923 kg / 4,239 lb) than the DEUTZ-ALLIS 9190 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 9190 and the 4494. |
| Which has the wider choice of gears? | 18Traktorenlexikon, “Deutz-Allis 9190” | 12Traktorenlexikon, “Case 4494” | AheadThe DEUTZ-ALLIS 9190 has 50% more forward gears (6 gears) than the J.I. Case 4494 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 9190 and the 4494. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Allis 9190” | 30 km/h (18.6 mph)Traktorenlexikon, “Case 4494” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 1000 rpmTraktorenlexikon, “Deutz-Allis 9190” | 1000 rpmTraktorenlexikon, “Case 4494” | EvenEven on PTO speeds: the same speeds (1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Allis 9190” | independentTraktorenlexikon, “Case 4494” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Allis 9190” | 4WDTraktorenlexikon, “Case 4494” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1989–1990 | 1984–1985 | Ahead (a fact, not an advantage)The DEUTZ-ALLIS 9190 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The DEUTZ-ALLIS 9190 has 80% more hydraulic flow (47.2 L/min / 12.5 gpm) than the J.I. Case 4494 (both pump flow, as stated by the source).
- The J.I. Case 4494 is 26% heavier (1,923 kg / 4,239 lb) than the DEUTZ-ALLIS 9190 (both unladen weight, as stated by the source).
- The DEUTZ-ALLIS 9190 has 50% more forward gears (6 gears) than the J.I. Case 4494 (both forward gears, as stated by the source).
- The DEUTZ-ALLIS 9190 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 9190 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 4494 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the 9190: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Allis 9190”); the 4494: lift through the full range 610 mm behind the ends, as stated by the source (Traktorenlexikon, “Case 4494”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources