DEUTZ-ALLIS 8010 or Eicher 3108?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 8010 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 3108 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The DEUTZ-ALLIS 8010 suits loader and hydraulic implement work better on this data: 237% (119.7 L/min / 31.6 gpm) more hydraulic flow.
- The Eicher 3108 suits road haulage better on this data: 33% (10.0 km/h / 6.2 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 8010 | 3108 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 78.7 kW (105.5 hp)Traktorenlexikon, “Deutz-Allis 8010” | 79 kW (106 hp)Traktorenlexikon, “Eicher 3108” | Not comparableNot comparable on power at the PTO shaft: the 8010 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 3108 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 8010 and the 3108. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 8010 and the 3108. |
| Which pumps more oil for implements? | 170.3 L/min (45.0 gpm)Traktorenlexikon, “Deutz-Allis 8010” | 50.6 L/min (13.4 gpm)Traktorenlexikon, “Eicher 3108” | AheadThe DEUTZ-ALLIS 8010 has 237% more hydraulic flow (119.7 L/min / 31.6 gpm) than the Eicher 3108 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,030 kg (6,680 lb)Traktorenlexikon, “Deutz-Allis 8010” | 6,730 kg (14,837 lb)Traktorenlexikon, “Eicher 3108” | Not comparableNot comparable on three-point lift: the 8010: lift 610 mm behind the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Allis 8010”); the 3108: lift at an unstated point, as stated by the source (Traktorenlexikon, “Eicher 3108”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 5,729 kg (12,630 lb)Traktorenlexikon, “Deutz-Allis 8010” | 5,400 kg (11,905 lb)Traktorenlexikon, “Eicher 3108” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 8010 and the 3108. |
| Which has the wider choice of gears? | 12 to 20Traktorenlexikon, “Deutz-Allis 8010” | 20Traktorenlexikon, “Eicher 3108” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 8010 and the 3108. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Allis 8010” | 40 km/h (24.9 mph)Traktorenlexikon, “Eicher 3108” | AheadThe Eicher 3108 has 33% more top speed (10.0 km/h / 6.2 mph) than the DEUTZ-ALLIS 8010 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Allis 8010” | 540/1000 rpmTraktorenlexikon, “Eicher 3108” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Allis 8010” | independentTraktorenlexikon, “Eicher 3108” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Allis 8010” | 4WDTraktorenlexikon, “Eicher 3108” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1988 | 1982–1990 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The DEUTZ-ALLIS 8010 has 237% more hydraulic flow (119.7 L/min / 31.6 gpm) than the Eicher 3108 (both pump flow, as stated by the source).
- The Eicher 3108 has 33% more top speed (10.0 km/h / 6.2 mph) than the DEUTZ-ALLIS 8010 (both top speed forward, as stated by the source).
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 8010 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 3108 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the 8010: lift 610 mm behind the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Allis 8010”); the 3108: lift at an unstated point, as stated by the source (Traktorenlexikon, “Eicher 3108”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources