DEUTZ-ALLIS 6060 or Deutz-Fahr DX 3.60?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 6060 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 3.60 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The DEUTZ-ALLIS 6060 suits loader and hydraulic implement work better on this data: 75% (30.9 L/min / 8.2 gpm) more hydraulic flow.
- The Deutz-Fahr DX 3.60 suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 6060 | DX 3.60 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 47.8 kW (64.1 hp)Traktorenlexikon, “Deutz-Allis 6060” | 47.6 kW (63.8 hp)Traktorenlexikon, “Deutz-Fahr DX 3.60” | Not comparableNot comparable on power at the PTO shaft: the 6060 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 3.60 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 6060 and the DX 3.60. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 6060 and the DX 3.60. |
| Which pumps more oil for implements? | 71.9 L/min (19.0 gpm)Traktorenlexikon, “Deutz-Allis 6060” | 41.0 L/min (10.8 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.60” | AheadThe DEUTZ-ALLIS 6060 has 75% more hydraulic flow (30.9 L/min / 8.2 gpm) than the Deutz-Fahr DX 3.60 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,588 kg (3,501 lb)Traktorenlexikon, “Deutz-Allis 6060” | 2,400 kg (5,291 lb)Traktorenlexikon, “Deutz-Fahr DX 3.60” | Not comparableNot comparable on three-point lift: the 6060: lift 610 mm behind the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Allis 6060”); the DX 3.60: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Fahr DX 3.60”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 2,585 kg (5,699 lb)Traktorenlexikon, “Deutz-Allis 6060” | 2,875 kg (6,338 lb)Traktorenlexikon, “Deutz-Fahr DX 3.60” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 3.60 is 11% heavier (290 kg / 639 lb) than the DEUTZ-ALLIS 6060 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | 4,700 kg (10,362 lb)Traktorenlexikon, “Deutz-Fahr DX 3.60” | No figureNo call on maximum permissible mass: no figure on record for the 6060. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Deutz-Allis 6060” | 16Traktorenlexikon, “Deutz-Fahr DX 3.60” | AheadThe Deutz-Fahr DX 3.60 has 100% more forward gears (8 gears) than the DEUTZ-ALLIS 6060 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 6060 and the DX 3.60. |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Deutz-Allis 6060” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 3.60” | AheadThe Deutz-Fahr DX 3.60 has 20% more top speed (5.0 km/h / 3.1 mph) than the DEUTZ-ALLIS 6060 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Deutz-Allis 6060” | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.60” | AheadThe Deutz-Fahr DX 3.60 offers 1000 rpm at the PTO, which the DEUTZ-ALLIS 6060 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Allis 6060” | — | No figureNo call on PTO independence: not stated for the DX 3.60. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Allis 6060” | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 3.60” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1988 | 1986–1996 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The DEUTZ-ALLIS 6060 has 75% more hydraulic flow (30.9 L/min / 8.2 gpm) than the Deutz-Fahr DX 3.60 (both pump flow, as stated by the source).
- The Deutz-Fahr DX 3.60 is 11% heavier (290 kg / 639 lb) than the DEUTZ-ALLIS 6060 (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 3.60 has 100% more forward gears (8 gears) than the DEUTZ-ALLIS 6060 (both forward gears, as stated by the source).
- The Deutz-Fahr DX 3.60 has 20% more top speed (5.0 km/h / 3.1 mph) than the DEUTZ-ALLIS 6060 (both top speed forward, as stated by the source).
- The Deutz-Fahr DX 3.60 offers 1000 rpm at the PTO, which the DEUTZ-ALLIS 6060 does not (as stated by the sources).
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 6060 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 3.60 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the 6060: lift 610 mm behind the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Allis 6060”); the DX 3.60: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Fahr DX 3.60”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources