Case-Steyr M 9094 a or VALMET 903/903-4?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the M 9094 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 903/903-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Case-Steyr M 9094a suits loader and hydraulic implement work better on this data: 12% (5.1 L/min / 1.3 gpm) more hydraulic flow and 48% (1,400 kg / 3,086 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | M 9094 a | 903/903-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 69.2 kW (92.8 hp)Traktorenlexikon, “Steyr M 9094 a” | 69.1 kW (92.7 hp)Traktorenlexikon, “Valmet 903” | Not comparableNot comparable on power at the PTO shaft: the M 9094 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 903/903-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the M 9094 a and the 903/903-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the M 9094 a and the 903/903-4. |
| Which pumps more oil for implements? | 48.1 L/min (12.7 gpm)Traktorenlexikon, “Steyr M 9094 a” | 43.0 L/min (11.4 gpm)Traktorenlexikon, “Valmet 903” | AheadThe Case-Steyr M 9094a has 12% more hydraulic flow (5.1 L/min / 1.3 gpm) than the VALMET 903/903-4 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 4,300 kg (9,480 lb)Traktorenlexikon, “Steyr M 9094 a” | 2,900 kg (6,393 lb)Traktorenlexikon, “Valmet 903” | AheadThe Case-Steyr M 9094a has 48% more lift (1,400 kg / 3,086 lb) than the VALMET 903/903-4 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,950 kg (8,708 lb)Traktorenlexikon, “Steyr M 9094 a” | 3,650 kg (8,047 lb)Traktorenlexikon, “Valmet 903” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 6,500 kg (14,330 lb)Traktorenlexikon, “Steyr M 9094 a” | — | No figureNo call on maximum permissible mass: no figure on record for the 903/903-4. |
| Which has the wider choice of gears? | 16 to 32Traktorenlexikon, “Steyr M 9094 a” | 16Traktorenlexikon, “Valmet 903” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the M 9094 a and the 903/903-4. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Steyr M 9094 a” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 903” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 430/540/1000 rpmTraktorenlexikon, “Steyr M 9094 a” | 540 rpmTraktorenlexikon, “Valmet 903” | AheadThe Case-Steyr M 9094a offers 1000 rpm at the PTO, which the VALMET 903/903-4 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Valmet 903” | No figureNo call on PTO independence: not stated for the M 9094 a. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Steyr M 9094 a” | Two-wheel or four-wheel driveTraktorenlexikon, “Valmet 903” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1994–2003 | 1979–1983 | Ahead (a fact, not an advantage)The Case-Steyr M 9094a is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Case-Steyr M 9094a has 12% more hydraulic flow (5.1 L/min / 1.3 gpm) than the VALMET 903/903-4 (both pump flow, as stated by the source).
- The Case-Steyr M 9094a has 48% more lift (1,400 kg / 3,086 lb) than the VALMET 903/903-4 (both lift at the hitch ends, as stated by the source).
- The Case-Steyr M 9094a offers 1000 rpm at the PTO, which the VALMET 903/903-4 does not (as stated by the sources).
- The Case-Steyr M 9094a is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the M 9094 a has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 903/903-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources