Case-IH MXM 190 Maxxum or John Deere 8110?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the MXM 190 Maxxum has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8110 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The John Deere 8110 suits loader and hydraulic implement work better on this data: 29% (27.2 L/min / 7.2 gpm) more hydraulic flow.
- The John Deere 8110 suits road haulage better on this data: 17% (2,000 kg / 4,409 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “similar machines”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | MXM 190 Maxxum | 8110 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 142.7 kW (191.4 hp)Traktorenlexikon, “Case-IH MXM190” | 143.5 kW (192.4 hp)Traktorenlexikon, “John Deere 8110” | Not comparableNot comparable on power at the PTO shaft: the MXM 190 Maxxum has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8110 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the MXM 190 Maxxum and the 8110. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the MXM 190 Maxxum and the 8110. |
| Which pumps more oil for implements? | 93.2 L/min (24.6 gpm)Traktorenlexikon, “Case-IH MXM190” | 120.4 L/min (31.8 gpm)Traktorenlexikon, “John Deere 8110” | AheadThe John Deere 8110 has 29% more hydraulic flow (27.2 L/min / 7.2 gpm) than the Case-IH MXM 190 Maxxum (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 6,985 kg (15,399 lb)Traktorenlexikon, “Case-IH MXM190” | — | No figureNo call on three-point lift: no figure on record for the 8110. |
| Which is heavier, for traction? | 8,010 kg (17,659 lb)Traktorenlexikon, “Case-IH MXM190” | 8,775 kg (19,346 lb)Traktorenlexikon, “John Deere 8110” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 12,000 kg (26,455 lb)Traktorenlexikon, “Case-IH MXM190” | 14,000 kg (30,865 lb)Traktorenlexikon, “John Deere 8110” | AheadThe John Deere 8110 has 17% higher maximum permissible mass (2,000 kg / 4,409 lb) than the Case-IH MXM 190 Maxxum (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 18 to 28Traktorenlexikon, “Case-IH MXM190” | 16Traktorenlexikon, “John Deere 8110” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the MXM 190 Maxxum and the 8110. |
| Which is faster on the road? | 40 km/h (24.9 mph) to 50 km/h (31.1 mph)Traktorenlexikon, “Case-IH MXM190” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “John Deere 8110” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540E/1000 rpmTraktorenlexikon, “Case-IH MXM190” | 540/1000 rpmOECD test report 1931, 2000 | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Case-IH MXM190” | independentTraktorenlexikon, “John Deere 8110” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Case-IH MXM190” | 4WDTraktorenlexikon, “John Deere 8110”; OECD test report 1931, 2000 | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 2002–2007 | 1999–2002 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 8110 has 29% more hydraulic flow (27.2 L/min / 7.2 gpm) than the Case-IH MXM 190 Maxxum (both pump flow, as stated by the source).
- The John Deere 8110 has 17% higher maximum permissible mass (2,000 kg / 4,409 lb) than the Case-IH MXM 190 Maxxum (both maximum permissible mass, as stated by the source).
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the MXM 190 Maxxum has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 8110 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift and a creeper range.
← Every figure for both machines, side by side, with sources